Question about Cars & Trucks

Open Question

Holden v8 308 head torque settings & tightening sequence

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

tburtk
  • 158 Answers

SOURCE: torque on 3.0 ford taurus head bolts

40 ftlbs then 73 ftlbs then recheck at 73 ftlbs

Posted on Feb 06, 2010

ZJLimited
  • 17970 Answers

SOURCE: what r the torque specifications

Check this procedure...

  1. Tighten the first design cylinder head bolts as follows:
    1. M11 bolts 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1,2,3,4,5,6,7,8): + 90 degrees.
    4. M11 bolts (9 and 10): + 50 degrees.
    5. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
  2. Tighten the second design cylinder head bolts as follows:
    1. M11 bolts (1-10) 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts (1-10) 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1-10): + 70 degrees.
    4. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

c409909.jpg

Fig. Cylinder head bolt tightening sequence-4.8L, 5.3L and 6.0L engines (click for zoom)


Install the cylinder head bolts in sequence to 22 ft. lbs. (30 Nm). The bolts must be tightened once, then be tightened again in sequence in the following order:
  1. Step 1: Short length bolt: (3, 4, 7, 8, 11, 12, 15, 16), plus 55 degrees.
  2. Step 2: Medium length bolt: (14, 17), plus 65 degrees.
  3. Step 3: Long length bolts: (1, 2, 5, 6, 9, 10, 13), plus 75 degrees.

7f05cb7.jpg

Fig. Cylinder head bolt tightening sequence-5.0L and 5.7L engines

Posted on Aug 04, 2010

SOURCE: suspect head gasket broken down between 5 & 6

Hi Dave Any adjustable torque wrench will be fine, as long as the correct settings AND sequence is followed.... ....Have you taken the head to have it checked for distortion....Its a good idea when doing any work which requires the removal of the cylinder head, especially so if the engine over heated at all....Have it checked at an engineering company and skimmed if need be.... ....Regards Johngee10

Posted on Oct 16, 2010

emissionwiz
  • 75051 Answers

SOURCE: cylinder head tightening sequence for ford mondeo 1.8i zetec petrol

Go to this LINK for the info in pdf format, the sequence is on page 16 of the pdf file.

Posted on Feb 16, 2012

Testimonial: "Great help...just the info I needed to do job. Thankyou very much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

1 Answer

What are the torque specifications and tightening sequence for cam journal and cylinder head for 2001 daewoo nubira 2.0 :(


  1. The torque settings for the cylinder head bolts on a daewoo ...

    www.answers.com > ... > Categories > Cars & Vehicles > Asian Car i need how much pression (torque) for head daewoo nubira 2001 2.0 ... What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and ...

Apr 15, 2011 | 2001 Daewoo Nubira

1 Answer

What are the torque settings for a 1997 audi a3 1.6 cylinder head


The torque settings for a 1997 Audi A3 1.6 cylinder head:

1. Tightening sequence
tdisline_167.jpg
2. Cylinder head instructions:
2.1. Renew bolts: Yes.

3. Tightening torques:
3.1. Stage 1 - Tighten: 40 Nm.
3.2. Stage 2 - Tighten: 90 degrees.
3.3. Stage 3 - Tighten: 90 degrees.


Please do rate my response. Thanks!

Jan 22, 2011 | Audi A3 Cars & Trucks

1 Answer

1998 FORD FESTIVA HEAD BOLT TORQUE SETTINGS & TIGHTENING SEQUENCE (1.5 LITRE ENGINE)


1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L
Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Aug 06, 2010 | Ford Focus Cars & Trucks

1 Answer

What is the cylinder head torque on a 2001 jeep cherokee


Please don't forget to rate....thanks:


e1aba13.gif

  1. Tighten the engine cylinder head bolts in sequence according to the following procedure

    CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  5. Tighten bolts in sequence:
  6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  7. Bolt 11 to 100 ft. lbs. (135 Nm).
  8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  9. Check all bolts in sequence to verify the correct torque.

Mar 06, 2010 | 2001 Jeep Cherokee

1 Answer

4g67 head tourqe settings


Hi,

Just to add to previous solution...

Assuming your head is straight & without defects, ensure you follow the correct tightening sequence diagram (see numbers) below:


Front of engine

i e
n 10 8 x
t h
a 4 6 a
k u
e 2 1 s
t
5 3
s s
i 7 9 i
d d
e e


1) Apply a small amount of engine oil to the thread section of the bolt and install so the chamfer of the washer faces upward.

2) In the proper tightening sequence (as shown above), torque bolts initially to 22 ft.lbs. (30Nm)

3) In the proper tightening sequence, now torque bolts to 45 ft.lbs. (61Nm)

4) In the proper tightening sequence, finally torque bolts to 68 ft.lbs. (92Nm)


Now you can Install the Camshaft sprocket and tighten it to 65 ft.lbs. (90Nm), while holding sprocket in place using the correct wrench.

Confirm proper timing mark alignment.

Cheers,

Aug 17, 2009 | 1991 Mitsubishi Galant

3 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

409 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...