Question about 1993 Mercury Grand Marquis

1 Answer

I purchased a 2011 mercury grand marquis door entry key pad was no provided, I would like to reprogram the 5 digit code to my use

Door entry 5 digit key pad was not available when I purchased the car, where do I find the factory 5 digit door code so I can reprogram the door code.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 12,650 Answers

Need to notify dealer for original code have vin and proof of ownership of vehicle available

Posted on Dec 30, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: entry code om drivers door

The keyless entry module is located in the rear of the vehicle on the driver's side. You will need to partially remove the left rear panel in the cargo area. You will then see the keyless entry module bolted behind a metal reinforcement bar. There is a sticker on the module that has the 5 digit entry code.

Posted on May 26, 2008

  • 10 Answers

SOURCE: keyless door pads

most dealerships use the zip code for your area to open all keyless entry cars if you bought it from a dealer--if you did buy it new you can ask the dealer to run an oasis on the truck & maybe get the code that way

Posted on Jun 28, 2008

  • 6 Answers

SOURCE: Factory Keyless Entry Code

mine was located on the right hinge in the trunk

Posted on Dec 23, 2008

chuck943
  • 783 Answers

SOURCE: Purchased a used 2006 Mercury Grand Marquis, did

Ok there are 2 ways to retrieve the key-less entry code. First and easiest way is to carry it to a shop that has a scan tool that can read pid data from the driver's door module .They can pull up that pid and display your code right on the screen.
The second and hardest method is to remove the driver's door panel to access the driver's door module and there will be a tag on it with the 5 digit code.
Yes you can program your own code into it however you must have the original code .Input the original code then hit the number 2 button then put in your own 5 digit code.This code will remain until you disconnect the battery or battery goes dead then it reverts back to the original.
You can also go to this website and download your owners manual for free. Just pick owner guide in the left task bar and input your vehicle information.

http://www.genuineservice.com/genuineservice/en/default?page=genuineService

Posted on Mar 09, 2009

  • 137 Answers

SOURCE: power locks, and keyless entry pad do not work.

if the battery in the entry pad is good then it needs to be reprogramed or the remote sensor is blowen

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse for the entry pad on a 1996 Mercury Grand Marquis?


Fuse #8 on the interior fuse panel and 20amp on the engine compartment fuse box, but if either of these were blown you would have several other things not working, door locks from any switch, dash board wouldn't light up, cluster radio heater control and d o on.if all this is working, I would start my testing at the door pad.they get little cracks in them over time and water gets inside and corrodes the switch, pad, internally. .ive done a lot up hete on east coast. .

Apr 30, 2014 | 1996 Mercury Grand Marquis

2 Answers

How do I change the keyless entry code for 2000 mercury grand marquis


1.locate and enter the factory set code(taped to the computer module also located on trunk lid. 2.press the 1/2button within 5 seconds of step 1. 3. enter your personal 5 digitcode within 5 seconds. Allthedoors will lock and unlock to confirm programming of the new code.

Apr 02, 2014 | 2000 Mercury Grand Marquis

2 Answers

Where do I find the keyless entry code for my 1999 Mercury Mountaineer? Then when I use the remote to unlock or lock the Mountaineer, the locks will pop up or the horn will blow or all four locks will...


TRY THIS REPROGRAMMING PROCEDURE. SWITCH THE IGNITION OFF TO ON 8 TIMES WITHIN 10 SECONDS. DOORS SHOULD LOCK THEN UNLOCK. PRESS ANY BUTTON ON THE FIRST REMOTE TRANSMITTER. DOORS SHOULD LOCK THEN UNLOCK. IF YOU HAVE ANOTHER CAR REMOTE REPROGRAM IT THE SAME WAY. WHEN DONE SWITCH IGNITION SWITCH OFF.

Jan 27, 2011 | 1999 Mercury Mountaineer

1 Answer

How do you change key less entry code on a 2003 mercury grand marquis


look on the trunk arm piston side for a code-this should be your permanent code number. to reset this number press this factory code number fo;;owed immediatly followed by the 1/2 button (within 5 seconds)!
- This will activate the code setting mode-- Enter your new 5 digit code and you are done( again you only have 5 seconds to do this or you have to start from the beginning) the doors should go through a cycling mode(lock /unlock) this tells you that it worked!!
(dont forget your new code) good luck also remember that you have a chip in your key-so dont try getting one made at the store to put in the ignition-you will end up stranded somewhere(not fun) good luck!

Nov 29, 2010 | 2003 Mercury Grand Marquis

1 Answer

HOW DO I RESET MY DOOR CODES FOR MY 1996 GRAND MARQUIS


Up to three personal entry codes may be programmed to the vehicle. To create your own personal entry code:

  • 1. Enter the factory set code.
  • 2. Within five seconds press the 1 � 2 on the keypad.
  • 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.
  • 4. Press 1 � 2, 3 � 4 or 5 � 6 to indicate which of the three personal entry code positions you wish to use.
  • 5. The doors will again lock then unlock to confirm that your personal key code has been programmed to the module.
Tips:

  • Do not set a code that uses five of the same number.
  • Do not use five numbers in sequential order.
  • The factory set code will work even if you have set your own personal code.
  • If you program a code to a position that already contains a set code, the previously-set code will be erased.

Erasing personal code
  • 1. Enter the factory set 5�digit code.
  • 2. Within five seconds, press the 1 � 2 on the keypad and release.
  • 3. Press and hold the 1 � 2 for two seconds. This must be done within five seconds of completing Step 2.
All personal codes are now erased and only the factory set 5�digit code will work.

Feb 17, 2010 | 1996 Mercury Grand Marquis

2 Answers

Where is sticker with factory 5 digit keyless entry code located on 2001 grand marquis


You should find it on the hinges in the trunklid and sometimes on a hood hinge. They can be in door jams and on door hinges. Your owners manual usually has a plastic card for your wallet.

If no success contact the dealer with your VIN#.

Nov 16, 2009 | 2001 Mercury Grand Marquis

2 Answers

I need to prograhm the key fob and also get the keypad code for the keyless entry


To program the fob; close all doors, unlock with door switch, turn key from off to on (without starting car) 8 times, ending in the on pos, the locks should lock and unlock then press the lock button on the fob, turn the key back. That should do it, if you get nothing, replace the battery in the fob. The keypad code is only retrievable through a scan tool. The dealer will charge a half hour to do that even though it takes less than 5 mins.

Aug 07, 2009 | 1997 Mercury Grand Marquis

1 Answer

Power locks, and keyless entry pad do not work. all fuses are good. 92 mercury grand marquis


if the battery in the entry pad is good then it needs to be reprogramed or the remote sensor is blowen

Jul 08, 2009 | 1992 Mercury Grand Marquis

1 Answer

Purchased a used 2006 Mercury Grand Marquis, did not have an original owners manual with factory code card in pack ( ordered an owners manual on line ) my question is how do I program the driver door...


Ok there are 2 ways to retrieve the key-less entry code. First and easiest way is to carry it to a shop that has a scan tool that can read pid data from the driver's door module .They can pull up that pid and display your code right on the screen.
The second and hardest method is to remove the driver's door panel to access the driver's door module and there will be a tag on it with the 5 digit code.
Yes you can program your own code into it however you must have the original code .Input the original code then hit the number 2 button then put in your own 5 digit code.This code will remain until you disconnect the battery or battery goes dead then it reverts back to the original.
You can also go to this website and download your owners manual for free. Just pick owner guide in the left task bar and input your vehicle information.

http://www.genuineservice.com/genuineservice/en/default?page=genuineService

Mar 09, 2009 | 2006 Mercury Grand Marquis

Not finding what you are looking for?
1993 Mercury Grand Marquis Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...