Question about 2003 Isuzu Rodeo

Open Question

Check engine light

When key is turned to ON, all the lights do there thing, the check eng light does its 2 or 3 flashes but keeps blinking at a faster rate, turning key to START nothing happens, also no pwr at 1st fuse marked engine inside cabb. engine is 3.0TD

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: 96 Isuzu Rodeo electrical problems (Car wont start)

It has to be an electrical connection as you say. The Anti Lock Brake system light is probably just a deprograming of the computer. Due to the electrical problem. Have you check for current at the starter ? Have sombody turn the key as if starting it. Then with a test light check for current at the starter connections. This will give you an idea whre to look for an open circuit or short.

Posted on Dec 23, 2008

Ad
  • 124 Answers

SOURCE: Turn key and it doesnt fire

one way to find out. spray starting fluid in the intake then try to start. if it starts then your problem is fuel related.

Posted on Mar 11, 2009

  • 34 Answers

SOURCE: 2001 isuzu rodeo has intermittent starting problems

check battery cables & terminals for tightness & corrosion.also check at starter.check starter bolts & actual starter for looseness.if no problems found your starter may be on its way out.next time it happens hit starter with hammer or heavy object if it starts right up get ready to replace it.good luck

Posted on May 23, 2009

  • 22 Answers

SOURCE: how to turn off check engine light 97 trooper

If you are a DIY'er you can get a OBDII scan tool that connects to your laptop that can tell you the error code and allow you to reset your check engine light. This will save you $80 each time over going to a mechanic for a diagnostic. They are easy to use and will help you know what the issues are if you do have to go to a mechanic.
Check out http://www.fitityourself.netau.net/OBDII.html
Sometime the check engine light comes on if you did not fit your gas cap tight enough. You need a code reader to find out the error code to help solve your problem.
If it is something simple (like a gas cap) and you do not want to get a code reader to find out what codes (problems) your vehicle computer is saying there is. You can try disconnecting the negative battery lead for 5 minutes. This should reset your check engine light. Drive and if it comes back on after some days, your problem is still there, therefore buy a code reader to get to the bottom of the issue.

Posted on Apr 14, 2010

  • 2 Answers

SOURCE: check engine light comes on

im not sure if it is your problem or not, but i have a 01 trooper and it was doing the same thing. it ended up being a weak fuel pump. autozone will lone a fuel pressure tester. that was how i determined my problem.

Posted on Jan 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light flashes car won't start


you can get the trouble codes out by turning key on off on off on then watch the check engine light it will flash a number of times n pause this will give you codes to take to the auto parts store n tell them they will know most of them the service writer at the dealer can find the rest (example) blink blink blink pause blink blink =32 there could be several so do it a couple times to make sure you get them right and get them all

Mar 15, 2012 | 1992 Plymouth Acclaim

Tip

How To Check & Reset Your 2002-2006 Nissan Altima Service Engine Soon (SES)...


The following directions will help you decode your 2002-2006 Nissan Altima's Service Engine Soon (SES) light and reset it.<br /> <br /> <span style="font-weight: bold;">Obtain The Trouble Code</span><br /> <ol> <li>Turn the ignition key to the ON position and wait three seconds.</li> <li>Put the accelerator pedal to the floor and release it five times in less than five seconds.</li> <li>Wait exactly seven seconds. Put the accelerator pedal to the floor for ten seconds until the SES light flashes.</li> <li>Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code.<br /></li></ol> <ul> <li>Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) </li> <li> The next three digits blink faster (0.3 second) and have a 1 second pause between digits.</li> <li>The ECM code repeats until you turn the ignition key to the OFF position.</li> <li>You can look up the trouble codes in the Service Manual.</li> <li>If you get four blinks of ten, or 0000, the ECM indicates no malfunction.<br /></li></ul> <br style="font-weight: bold;" /><span style="font-weight: bold;">Clear The Trouble Code</span><br /> <ol> <li> Clear the code and the SES light by holding the accelerator pedal down to the floor for 10 seconds or more while the SES light is blinking.</li> <li>When the pedal is released, the ECM will erase the trouble code(s).</li></ol>

on Feb 15, 2011 | 2002 Nissan Altima

1 Answer

Where do I find the wires that I apprently need to cross to get the check engine light to flash in order to get the codes?


Remove the kick panel just beside the left foot rest on the driver's side.
2) Locate blue wires.
3) Locate black connector. Hold it notch up.
4) With ignition off, insert one of the wires into top row, 2nd pin from left.
5) Turn key to on position, but do not start the car.
6) Watch blinky check engine light on dashboard. Count blinks. Long blinks = 10, Short blinks = 1.
7) Keep watching blinky light until you get mesmorized.


To clear codes (after problem has been resolved):
1) With engine off, stick the blue wires to 1st and 2nd pin in the top row counting from left on the

black connector, with notch facing up.
2) Start car. Shut off car. Remove pins.
3) Read codes to make sure they are clear. No codes = steady blinks at 1/4 second intervals. yhis is for the 94, 92 should be the same. have a good day !!


Jun 05, 2011 | 1994 Subaru SVX

1 Answer

It is Vitara sidekick 1997 model. Water temp sensor is replaced, the fault code erased, when I start the engine and drive, every thing looks nice, but when I switch off the Ig key and start the engine next...


you can get codes with out scan tool, this is done by counting the engine light flashes, for example a long flash is the first didgt and then faster blinks would be the next number, for example long flash long flash long flash= 3 then fast flash ,fast flash, fast flash, fast flash =4 which would be code 34, to get the codes look in the engine compartment in front of the battery is the connector, you will need a small wire to jump two terminals, jump terminals with wire then turn key on and count flashes, i will give you a diagram to locate connector and it will show you which terminals to jump look at connetor closely to make sure you are jumping the correct terminals, you can turn the key off and on to restart the codes again,this may take you a few trys to get the hang of it but you can restart the codes by just turning the key off and back on, when your done just remove the jumper wire,also a diagram is enclosed to show you how the flashes go, hope this helps ,good luck.

Mar 05, 2011 | 1993 Suzuki Sidekick

1 Answer

I have a 2001 saturn sw and replace the ign and the secuirty light flashs and eng will not crank.i dissconnected the battery over night and still the same. thanks steve


Hello: Try this procedure, Turn key on attempt to start engine leave key on, the security light should be blinking, wait 10 minutes. The security light should be off. Turn key off for 10 seconds, turn key back on (DO NOT ATTEMPT TO START) wait another 10 minutes. Turn key off for 10 seconds. Do the procedure again as in step 2. At the end of the third time turn key off then ten seconds later attempt to start the car. It should start.

Nov 25, 2010 | 2001 Saturn SL

2 Answers

Toyota Camry 1998 dashboard light on


yes, that is called a "check eng" light, this may have came on for many different reasons, low eng oil level, low eng. oil pressure, eng. may be misfireing, eng. may be overheating etc. many things can cause this. get hold of a diagnostic scanner and scan for codes. or take it to any shop. theyll scan for you

Apr 06, 2010 | 1998 Toyota Camry

2 Answers

1999 Nissan Maxama air bag light keeps flashing 11


Have it checked by a professional as soon as possible, airbag has a problem wich can be as simple as a short in the wiring or as harmful as the possibility of deploying airbags without any warning. Please take advice.

Dec 26, 2009 | 1999 Nissan Maxima

2 Answers

ANTI THEFT LIGHT KEEPS FLASHING ON AND OFF


Did you steal it? I heard about you thieves who steal cars then put new transmissions in!!
Seriously, try this, it may help...
Put the key in the ignition, and turn forward all the way just before cranking. Then within 5 seconds, locate, press and hold in the valet/overide button, found under the dash area, (push button, spring loaded) until the installed LED (the blinking light) in your dash area goes on solid, and the siren chirps once. (Your valet switch might be the toggle (on/off) type. in this case, key on, flip switch in opposite direction, then turn the key off.) This should reset the alarm, and reset the grounded relay on the starter wire, allowing you to start the engine. At this point, the only thing working would be the keyless entry from the alarm, if it came equipped that way. Just Repeat these steps to place it back to usable armed mode. You may get 2 chirps, confirming it, and the lights may flash twice as well. That should do it. Check out www.explorerforum.com

Dec 04, 2009 | 1996 Ford Explorer

3 Answers

Reset change engine oil light


Information taken from: http://www.idavette.net/tech/oilreset.htm

[quote]
The "Change Oil" indicator is reset by using a sequence of Driver Information Center (DIC) key presses as follows:

1. Turn ignition "ON", but do not start engine. (ALDL pin "G" should NOT be grounded.)
2. Press the "ENG/MET" button and release, then, within 5 seconds, press it again.
3. Within 5 seconds of Step 2, press and hold the "GAUGES" button. While the button is held, the "Change Oil" indicator will flash.
4. Continue holding the "GAUGES" button until the "Change Oil" indicator stops flashing and goes out, indicating successful completion of the reset cycle. This should take about 10 seconds.
If it does not successfully reset, turn ignition "OFF" and repeat the procedure from Step 1.
[/quote]

Nov 16, 2009 | 1991 Chevrolet Corvette

1 Answer

Check engine light even after servicing to correct


you have a misfire, the eng light flashes,avoid driving it , or it can damage the cat converter,i dont know what repair was done, but if you replaced the spark plugs one may be damaged, or incorrect plug gap can cause this concern.

Oct 11, 2009 | Audi A4 Cars & Trucks

Not finding what you are looking for?
2003 Isuzu Rodeo Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...