Question about 2008 Toyota Sienna

Open Question

How to remove hood liner clips sienna van - 2008 Toyota Sienna

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take off a fender


3 bolts under the hood. one in the door jamb. four under the car behind the wheel well liner. One at the very front of the side skirt underneath.

Read more: http://www.xcardiag.com/

May 08, 2014 | 2005 Toyota Sienna

1 Answer

Where can i find the ac relay on 2000 sienna


Its the white relay in the fuse box under the hood of the van its marked (ccm) for compressure clutch magnet.

Apr 15, 2011 | 2000 Toyota Sienna

2 Answers

Help how do i change the license plate bulb on my 2004 corolla?


I just replaced my 2 bulbs an hour ago in my garage.
1. Pry off all the clips that hold the liner. I used a cloth covered spatula, so
as not to chip the paint, to pull out the liner a little bit and used my
index and middle finger to pull back the clip and the liner, very slowly to
prevent breakage. When all the clips are off, the liner will fall, no need
to remove the emergency release handle.
2. Press the tiny release lock that hold the wires in the socket and pull
out the wires, carefully.
3. Turn the socket 1/4 the the left carefully, while putting a little pressure
upward, then the socket will release.
4. Pull the bulb staight out and replace it.
5. Reverse the procedure and voila! A ton of money saved!!!!!!
MVC.

Jan 03, 2011 | Toyota Corolla Cars & Trucks

1 Answer

How to replace license plate lights


    Follow the Steps on how to replace license plate light on your car.

    1. Open the trunk and locate the trunk liner retainer clips.Use the Phillips head screwdriver to loosen the center plastic screw of the retainer clip about 1/4 turn, just enough to raise the head of the screw from the base of the clip. Pull the screw up, and lift the clip out of the liner. Use a flathead screwdriver to help pry it out. Remove enough of the clips to allow access to the license plate light sockets. Pull the liner back.

    2. Remove the emergency trunk release handle by popping off the top cover of the handle. Use the needle nose pliers to gently squeeze the prongs on the shaft, while removing the handle.

    3. Unplug the wire harness from the license plate light bulb socket the release clip on the side of the outlet.Twist the license plate light bulb socket 1/4 turn counterclockwise, using the needle nose pliers again. Do not apply too much pressure to the pliers; you may damage the socket.

    4. Remove the bulb from the socket, and replace it with a new one.

    5. Replace the socket into the socket assembly, and plug the wire harness back in. Test the bulb by turning on the lights of the Corolla, then turn them off again.

    6. Replace the trunk emergency release handle, and replace the hood liner and the retainer clips. Remove the old bulb and tools, and close the trunk.

Dec 22, 2010 | 1995 Toyota Corolla

1 Answer

Rear spark plug replacement on sienna 04


a rachet a extenion and a swivel go from under the van make sure you check the gap

May 04, 2010 | 2004 Toyota Sienna

1 Answer

Changing the rear disk brakes on a 06 toyota sienna, what is the process?


-Set up jack and properly block front tires.

-Do not set parking break as this may hender removing the rear calipers. Open hood and remove the brake resevoir cap.

-Remove hubcaps if applicable,

-Loosen Lugnuts but do not remove,

-Jack up van,

-Remove tire.

-Caliper should be visible. There are two bolts or hex heads on the back side that can be a pain to remove sometimes.

-Pull the caliper off the rotor, It is recomended to have the rotors turned or replaced. With the old pad still in place, take a c clamp or brake caliper squeezer and compress the caliper

-remove old pad, take note for the reinstall of the new pad.

-reverse the steps. This is a simple break down. Hope it helps

Feb 07, 2010 | 2006 Toyota Sienna

1 Answer

How do I replace the dome light bulb in my sienna van? the housing does not pop out..


It's easy - the plastic covers will pop off if you gently use a screw driver to pry the three points of contact on each cover. There are 2 posts in the middle going into the outside edge, and one clip at the end. The covers come off and you can easily replace the bulbs - forget about opening the garage door oopener and removing the screws - that won't work (I tried!).

Dec 05, 2009 | 2002 Toyota Sienna

1 Answer

2003 Sienna tail lights don't work when headlights are on


Look under the dashboard, next to/above the park brake pedal, for the interior fuse box. It has a black plastic cover. Remove the TAIL fuse, and see if it is blown. This should get you fixed up. Hope this helps, and Thanks for choosing FixYa.

Nov 11, 2008 | 2008 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...