Question about 2000 Ford Mustang

1 Answer

My a/c works but when i turn on the heat it only blows cold in my 2000 ford mustang coupe

The heater valve door does open but we cant get the heat to work the a/c works grat and the heater coil is not cloged n theres a brand new thermastat in it as well if anyone has any suggestions plz let me know

Posted by on

  • 4 more comments 
  • rose
    rose Dec 29, 2013

    the blender door actuator moves freely right to left

  • Brock Saint Aoro
    Brock Saint Aoro Dec 30, 2013

    you took the actuator off the blender door and turned the dial and watched it move? the door has a piece of plastic between the door and the actuator that can break as well. and we're talking about the actuator that is under the dash on the passenger side near the console? your car has 3 actuators on it

  • rose
    rose Dec 30, 2013

    no we didnt know all that we checked one behind the radio we rare going to get up early tomorrow and check that out thank u so much and ill get back to you tomorrow

  • rose
    rose Dec 30, 2013

    Add a Commentwhere are the 3 located at?

  • Brock Saint Aoro
    Brock Saint Aoro Dec 30, 2013

    Temperature Blend Door Actuator


    Lower the glove compartment.
    Disconnect the temperature blend door actuator electrical connector.
    Remove the 2 temperature blend door actuator screws.
    Remove the temperature blend door actuator.
    To install, reverse the removal procedure.


    Vacuum Control Motor-Air Damper Door


    Remove the instrument panel.
    Disconnect the vacuum hose.
    Remove the vacuum control motor.
    Remove the steel clip.
    Loosen the nuts.

    To install:

    Installation is the reverse the removal procedure.

    Vacuum Control Motor-Air Inlet Duct Door


    Remove the instrument panel.
    Disconnect the vacuum hose.
    Disconnect the control arm.
    Remove the screws and remove the vacuum control motor


    To install:

    Installation is the reverse the removal procedure.

    Lower the glove compartment.
    Disconnect the air inlet mode door actuator electrical connector.
    Remove the 2 air inlet mode door actuator screws.
    Remove the air inlet mode door actuator.


    To install:

    Installation is the reverse the removal procedure.

  • Brock Saint Aoro
    Brock Saint Aoro Dec 30, 2013

    sorry didn't mean to post it twice

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 131 Answers

Blender door actuator, under passenger side of the dash about 6 inches to the left "toward the center console" of the blower motor.

Posted on Dec 29, 2013

Testimonial: "the blender door actuator moves freely right to left"

  • Brock Saint Aoro
    Brock Saint Aoro Dec 30, 2013

    Temperature Blend Door Actuator Lower the glove compartment. Disconnect the temperature blend door actuator electrical connector. Remove the 2 temperature blend door actuator screws. Remove the temperature blend door actuator. To install, reverse the removal procedure. Click image to see an enlarged view Fig. Temperature blend door actuator (2005 Models) Vacuum Control Motor-Air Damper Door Remove the instrument panel. Disconnect the vacuum hose. Remove the vacuum control motor. Remove the steel clip. Loosen the nuts. Click image to see an enlarged view Fig. Remove the vacuum control motor. To install: Installation is the reverse the removal procedure. Vacuum Control Motor-Air Inlet Duct Door Remove the instrument panel. Disconnect the vacuum hose. Disconnect the control arm. Remove the screws and remove the vacuum control motor. Click image to see an enlarged view Fig. Remove the screws and remove the vacuum control motor To install: Installation is the reverse the removal procedure. Lower the glove compartment. Disconnect the air inlet mode door actuator electrical connector. Remove the 2 air inlet mode door actuator screws. Remove the air inlet mode door actuator. Click image to see an enlarged view Fig. Vacuum control motor-air inlet duct door To install: Installation is the reverse the removal procedure.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Ford windstar 2001

Replace the heater actuator switch it is not allowing the door to open, Ours did the same thing so I relaced it . it cost 90.00 from ford

Posted on Nov 02, 2008

  • 122 Answers

SOURCE: 2000 Ford Taurus-- Heater not working.

heater valve to let the coolant into the heater core is not working the heater cluster in your dash that controls the heat might be bad. it also controls the fan and air conditioner

Posted on Dec 27, 2008

localwonder
  • 6784 Answers

SOURCE: heater is blowing but its cold air not hot air 2000 expedition

Make sure the heater core is in the open position by using the shut off valve and turning it to open. next, you may have a malfunction in the direction door the directs the air flow in the dash. a lever may have become lose or separated. may be a bad servo motor not directing the door to move to the heater position. i would start by checking that shut off valve first on the heater core.

Posted on Mar 13, 2009

  • 1 Answer

SOURCE: rear heater core works great fan works but doesn't

checked vacuum hose works good now

Posted on Oct 20, 2009

  • 1 Answer

SOURCE: heater blows cold air on my 2000 Ford Expedition

Have had the same problem 2000 ford expedition. got it working good now

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat blow cold air


probably heater door that allows heat into the interior not working or whatever controls you have that opens this door defective...1st make sure ur getting heat into your heater core by feeling both hoses which should both be hot, if one not hot then perhaps the valve that opens the water flow through the heater is not opening...sometimes u can see this visibly whereas you can then try to manually open it...

Dec 12, 2013 | 2000 Pontiac Grand Am GT

1 Answer

2000 ford expedition 5.4 heat is cold. When heat is on low its warm, if i turn the blower on high its cold. I changed thermistat, had the heater core back flushed twice and it flows with no debris, the...


if the heater hoses are hot the only thing it could be is a blend door, if you can hear the door moving its not closing all the way, those are made of plastic and are common to brake at the actuator you will hear the actuator work but it will only partially close and open the door

Dec 15, 2010 | 2000 Ford Expedition

1 Answer

I have a 2000 ford mustang and the heat is not working. cold air comes out when i turn the heat on.


check to make sure the heater control valve is opening/ check to make sure that you have pressure in the radiator (about 14-19 lbs) be careful not to get burned put a towel over the cap before opening.!
if you pressure! check to make sure that the thermastat is good if thats ok ..check to see if you have water going through the heater core if you do check to see if the door is opening inside. between the heater & the air conditioning if you have air
sometimes critters get into the heater box to keep warm if all else failes change the radiator

Feb 25, 2010 | 2000 Ford Mustang

2 Answers

Heater is blowing but its cold air not hot air 2000 expedition


Make sure the heater core is in the open position by using the shut off valve and turning it to open. next, you may have a malfunction in the direction door the directs the air flow in the dash. a lever may have become lose or separated. may be a bad servo motor not directing the door to move to the heater position. i would start by checking that shut off valve first on the heater core.

Mar 13, 2009 | 2000 Ford Expedition

1 Answer

No back heat in Expedition, Blows cold air but front works fine


Shelly,

Buy used parts at car-part.com. Look on page with * to find the cheapest part. Coud be your temp blend door (#2) may not be moving back and forth. Or, you are not getting hot water to the rear heater core.

3d53924.gif
You may have to crawl under the truck and feel the heater hoses to see if they are hot. You will find a group of 4 lines, 2 for heater and 2 for a/c. If hot, you know hot water is getting back to the heater core. If not, there may be a hot water vave that's not working. Not sure if EXP. has a water valve for rear.

Let us know what you you find. Good luck.

Feb 22, 2009 | 2000 Ford Expedition

4 Answers

Heater doesn't work in car


i have a ford fiesta 51 plate,when i turn on heater i only have cold air the thermostat has been fixed and coolant levels are ok heatin hoses are all hot,but inside the car its still blowing cold

Oct 19, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
2000 Ford Mustang Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...