Question about Toyota Cars & Trucks

Open Question

Toyota remotes not working p/n 08191-20810

Remotes not working. Replaced battery's and still no led light when I press the button.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: Key remote battery replacement

Make sure that you have the Batteries Installed Correctly. If these Remotes take the Flat Round Batteries, Look and see if it tells you inside the Remote which way to Put the + On the Battery. Most of them have the + at the Top during Install. If it takes the Small Regular Battery, Looks like a Smaller AAA. You will need to Push the Connectors in a Bit Before you Install the Battery to make Sure that It connects with Both ends. Please Rate my Response, I need all the Help that I can Get! Thanks!

Posted on Jan 26, 2009

Ad
  • 15 Answers

SOURCE: 1996 Toyota Celica remote security system no longer works

Hi, Contact your dealer and get instructions for reprogramming your remotes. When a security system loses power for an extended amount of time the programming for the remotes are lost.

Posted on Mar 09, 2009

  • 1 Answer

SOURCE: programming keyless remote

2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Posted on Jul 10, 2009

  • 2 Answers

SOURCE: my renault laguna 1999 rt remote key fob wont work?

IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Posted on Dec 02, 2009

  • 148 Answers

SOURCE: Keyless remotes won't work after battery change.

Remote has to be reprogramed. Look in owners for proceedure. If you don't have a manual call the dealer. May have to take vehicle to them to reprogram it with a scantool

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had a avital remote start pot on a 2004 chevy venture van. everything worked ok for a month then the remote locks, poer windows and dome lights quit working. are they all connected together for the...


Avital is one brand of remote starter that features easy-to-use keyless remotes. These remotes can be programmed wirelessly to your engine and then added to your keychain. Once programmed, you will be able to use the remote from as far as a couple hundred feet away in your house, the street or a parking lot. If your remote is not working, you can troubleshoot the remote and get it resynced in seconds.
  • Enter your caricon1.png, leave your driver's door open and insert your key into the ignition.
  • 2 Turn the ignition to the "On" position and press and release the "Valet" button on your remote.
  • Press and hold the "Valet" switch again after releasing the first time and wait for the system's siren to chirp and the LED lighticon1.png to blink.

  • 4 Continue holding the "Valet" button and then press the starter button on your remote.
  • 5 Wait for another chirp and release both buttons to complete the process.

  • Apr 08, 2014 | Cars & Trucks

    1 Answer

    Cant lock doors with remote. replaced motors in the door locks. can lock only manually


    Is the battery in the remote any good?
    When you press the remote button do you have an led light up or blinks?

    Nov 05, 2013 | 2006 Toyota RAV4

    1 Answer

    The remote key chain transmitter stopped working all of a sudden, replaced battery still won't work.


    I believe with the remotes on your vehicle needs to be reset to vehicle. You will need all remotes and in the owners manual it will tell you how many times you need to turn the ignition to the on/off position and then you will hit a button on the remote and it syncs them up again. It will probably be something like turn the key to the on position then turn off like 3 times then leave in on position then press a button on the remote, the dash lights will flash to inform you that the remote is now sync'd and now you will press a button on second remote. Good luck.

    Feb 18, 2011 | 2004 Ford Explorer

    1 Answer

    I have an X reg Toyota Yaris the key has worked OK for yeras but now the remote will only unlock the car it will not lock it. We have changed the battery and have the same problem, the red light is lit...


    Try reprograming the remote. Some models allow for you to do your own programing from the console. If it does not work E-bay has a wide selection of OEM inexpensive remotes. Good luck

    Sep 17, 2010 | Toyota Yaris Cars & Trucks

    1 Answer

    2001 ml320, remotes quit working. new batteries,


    Synchronization
    Turn ignition switch to position II. Turn ignition switch to position 0 and remove key. Within 1 minute: Press and hold key lock button. Press unlock button 5 times. Remote control should now operate system. If not: Repeat procedure.
    Programming
    When
    Key remote control added or replaced. System malfunction.
    How
    Keys can only be programmed using diagnostic equipment

    Jan 09, 2010 | 2002 Mercedes-Benz C-Class

    2 Answers

    1996 Toyota Celica remote security system no longer works


    Hi, Contact your dealer and get instructions for reprogramming your remotes. When a security system loses power for an extended amount of time the programming for the remotes are lost.

    Mar 09, 2009 | 1996 Toyota Celica

    1 Answer

    Remote key fob will not work-battery replaced


    VW/AUDI/SEAT/SKODA



    Remote Control Programming (1997 ON)

    Procedure
    1. Switch Ignition ON and leave the key in the ignition.

    2. Mechanically lock the vehicle using the Drivers door using a second
    key.

    3. Using the remote control press the Unlock button once, and the horn
    will sound once.

    4. Wait 6 seconds and press the unlock button once to activate the coding
    procedure. The remote control will now be programmed.

    NOTE : When performing programming on additional remotes the procedure
    is the same, except you press the unlock button 2, 3 or 4 times for the
    different remote.

    For example : If programming 2 remotes press the unlock button twice with
    a 1 second interval between each press, repeat for 3 and 4 remotes.

    5. Switch Ignition OFF.

    6. Remove key from ignition and check for operation.

    7. The coding procedure can be repeated up to 4 times for additional remotes.

    8. The ignition must be switched OFF between programming each remote
    control.

    Remote Control Erasing (1997 ON)

    Procedure
    1. Switch Ignition ON and leave the key in the ignition.

    2. Mechanically lock the vehicle using the Drivers door using a second
    key.

    3. Press the remote control unlock button 5 times in 1 second intervals.
    A short horn will sound.

    4. Wait 6 seconds and press the unlock button once to activate memory
    erase.

    5. Switch ignition OFF, all remotes are now erased.

    Dec 24, 2008 | 2004 Volkswagen New Beetle Convertible

    1 Answer

    Keyless entry not working


    Try re-programming the remotes, here is the procedure for your car.
    JAGUAR
    XJ8 Remote Control Programming
    1. Unlock the trunk with key.
    2. Turn Ignition on.
    3. Warning light on dash comes on.
    4. When they go out, lift arm rest, inside their is a valley button, Press 5 times within 5 secs of lights on dash going out, Horn & Lights Flash.
    5. Press any button on remote, remote programmed

    Dec 11, 2008 | 2006 Jaguar XJ8

    3 Answers

    Changing a battery on a Cobra 7777 remote control


    The battery in the 7777 remote is a CR2032. If upon changing the battery the remote fails to work then you should stand next to the car and hold down both remote buttons for around 10 seconds to reactivate it. The remotes LED will flicker rapidly during this process. Keep holding both buttons until the LED stops flickering then release both buttons. The LED should now be on constant, press the larger of the two buttons and the remote should now be re-synced.
    Note: This procedure is not to program the remote to the alarm, but to re-synchronise it.

    Aug 20, 2008 | 1999 Mazda 626

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    164 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    80637 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...