Question about 2000 Toyota Tundra

Open Question

Loose antenna how to tighten

What to do to tighten antenna how to get access to bottom of antenna

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mrgreenz
  • 962 Answers

SOURCE: Access to tighten my antenna

Is it a power antenna ? or a regular antenna ? you may have to remove the wheel well liner to acess the antenna.Remove the clips that attach the liner.Hope this helps.

Posted on Oct 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I tighten the turn signal arm on 1977 Buick limited. It works however loose in the up and down position.


I am pretty sure the screw or bolt has come loose lever to signal switch. Steering wheel etc. will have to be removed to access loose
fastener
link below is not your car, but shows the basics of what has to be done to access switch.
press the helpful button.
Turn Signal Cancelling Cam Replacement

Jan 22, 2016 | Buick Cars & Trucks

1 Answer

Antenna removal


The antenna just twists off, dropping the glove box down will give you access to the antenna wire from stereo to antenna.

Aug 18, 2014 | 2004 Ford F150

2 Answers

I went to a car wash yesterday and now the radio in my 1998 Acura CL has lots of static on it. What is the solution?


There is a chance your antenna is loose. Try to tighten it and see if that helps. It might need adjusted

Feb 09, 2011 | Acura CL Cars & Trucks

3 Answers

How do you replace the atenna mast for 2005 sierra.


How do I install a new antenna on my GMC 05 2500 Sierra. I have to replace the base because it broke off. I've taken the dash off. But cannot seem to fish wire through the firewall.

Nov 26, 2010 | 2005 GMC Sierra

2 Answers

My antena wont go down ,and the motor wont go off , even when the car is shut off .


Unplug the harness to the ant.It will not go off,until you replace the whole ant.mass.The gear(plastic)are stripped out,and the motor can not sense that the any.is moving.

Jan 19, 2010 | 1991 Oldsmobile Eighty Eight

1 Answer

How do I install the power antenna? I have a replacement, and the wiring is there, but I don't see how to mount the part.


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Lower the antenna and remove the luggage compartment trim panel.
  2. Disconnect the lead-in cable from the antenna and ground strap.
  3. Disconnect the antenna motor wires at the connectors and disconnect the control box connectors.
  4. Remove the top mounting nut and stanchion assembly.
  5. Remove the two nuts retaining the antenna bracket assembly to the quarter panel.
  6. Remove the antenna assembly from the vehicle.
8617042.gif
Some antennas require a special socket to remove the locknut

6210b68.gif
Once its loose the nut can be removed by hand. Sometimes it can be twisted off with a needle nose pliers, but that usually ruins the tool

afa5165.gif
The antenna mounts in the luggage compartment against the support member

abce961.gif
The motor and housing sit on a stand that is bolted to the support member

0ee099b.gif
Unplug the antenna lead from the staff tube

9b0f741.gif
Unplug the connector to the motor

fb68086.gif
Unplug the connector to the relay

d275fd1.gif
Its easier to remove the antennae from the support to gain access to the ground strap screws

To install:
NOTE Correct sequencing for installation is important to prevent water leakage or dimpling of the quarter panel

  1. Connect the antenna cable, power connector and control box connector.
  2. Insert the antenna mast through the quarter panel hole and position bracket on mounting studs in the luggage compartment.
  3. Install the stanchion assembly.
  4. Loosely install the two bracket retaining nuts.
  5. Install the top-mounting nut.
  6. Tighten the bracket retaining nuts.
  7. Install the ground strap.

Nov 19, 2009 | 1990 Lincoln Continental

1 Answer

I have a Saturn 2002 coupe and the antenna is loose. How can I tighten it without taking off the front panel?


The base of the antenna should be nut shaped so you can tighten it with a wrench

Sep 08, 2009 | 2000 Saturn SL

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

1 Answer

Gear stick seems loose when in 5th gear on Toyota Hilux Surf


you can replace the bush on the bottom of the gear stick accessable through the top of gearbox it may tighten it up a bit

Apr 09, 2009 | 1994 Toyota 4Runner

1 Answer

Access to tighten my antenna


Is it a power antenna ? or a regular antenna ? you may have to remove the wheel well liner to acess the antenna.Remove the clips that attach the liner.Hope this helps.

Jun 26, 2008 | 2000 Toyota Tundra

Not finding what you are looking for?
2000 Toyota Tundra Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...