Question about 2008 Chevrolet Equinox
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The torque converter clutch circuit may be at fault. The best way to determine the problem is to have a scanner/computer to read check engine codes.
Posted on May 06, 2009
I have had exactly the same problem on and off for 3 years now - and just solved it last week thanks to another computer site. Remove and disassemble both grounds from the top of both the left and right frame rails adjacent to the front corners of the engine block. Completely clean the green corrosion from the internal parts with fine sandpaper and add dielectric grease then re-assemble. Clean the mounting bolt and frame hole while you're at it. Sounds time consuming and difficult, but it ain't. No more than 45 minutes combined. I am a technical airhead so if I can do it so can you. What clued me in was the problem always occurred around wet or humid weather. Also, the clock would always lose time overnite. That has ceased also. Good luck. Anyone know why my left headlite, when deployed, vibrates and shimmys??? Sully email@example.com
Posted on Jul 07, 2009
po455 is Probable Cause[s]
1. Defective, loose or missing fuel cap
2. EVAP canister broke, hose cracked or not connected
3. Purge or vent solenoid defective
4 . Vacuum leak at engine po121 code po121 means Throttle Position Sensor/Switch A Circuit Range/Performance Problem . it is usually indicative of a faulty throttle position sensor or faulty wiring harness in the engine bay.
Posted on Feb 27, 2010
Traction control only works when one wheel is spinning faster than the other it trys to even them out so it wont spin...sometimes if one of the wheels come off the ground in an uneven area or if you take a turn too fast and one wheel turns when the other one dont it is designed to operate.
I would remove all wheels and check the braking system...Is it 4 wheel disc or rear drum ?
If it has rear drums you could have a wheel cylinder leak that will sometimes lock the wheel because of fluid contamination....This would cause both lights to come on...If you find no problems
sometimes the abs sensor builds up fragments on the magnet and makes the light come on...
or if the abs sensor is not close enough to the exciter ring it will make the light come on because it will be out of adjustment.....all you do is press the sensor inward until it barely touches the ring and it will adjust itself....You can sometimes clean the magnet if it is contaminated and make the light go off ( only after you reach 6 to 15 mph. it will go off ).If it dont go off you have to buy a sensor.
Also make sure all tires have same amount and plenty of air to keep vehicle in balance/level.
Posted on Feb 21, 2011
Tips for a great answer:
Jan 01, 2016 | 2007 Chevrolet Chevrolet Equinox LT
Jun 05, 2015 | Cars & Trucks
Jan 11, 2015 | 2008 Pontiac Torrent
Whenever this warning or any other stays on in the dash it is indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)
Sep 19, 2012 | 2000 Cadillac DeVille
Feb 24, 2012 | 1999 Mazda 626
Aug 15, 2011 | 2003 Toyota Sequoia
Mar 05, 2010 | 2006 Jeep Grand Cherokee
Nov 18, 2009 | Cadillac DeVille Cars & Trucks
Oct 14, 2009 | 2004 Oldsmobile Alero
Feb 21, 2009 | 2001 Hyundai Elantra
21 people viewed this question
Usually answered in minutes!