Question about 1999 Chevrolet Silverado 1500

1 Answer

Trying to remove trany pan. All bolts are out. Pan is loose but is hung up on something. Possibly a cable bracket. Help!

Trying to remove trany pan on 1999 silverado 4X4. all bolts are out pan is loose but there is a trany shift cable bracket that seems to be in the way and I don't know how to remove it (or don't I have to)

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It takes a star driver from above to loosen the "clip". Helps to have small hands and there is not much room to work with.

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing oil pan from saturn l300


the ac compressor bolts to the side of the pan and the trans bracket near the pass side of the trans

Sep 12, 2012 | 2003 Saturn L-Series

1 Answer

I'm trying to remove my oil pan on a 2000 Silverado 1500 with a 4.3L V6. I've removed all of the bolts, the starter, the transmission cooling lines, the oil level sensor bracket, the front wire bracket,...


I am not sure, But there could be six more bolts to remove. They will be on the side of the pan, about half way up. three on each side. Sorry for guessing, I work on to many makes and models. Also the gaskets do hold the pan on tight sometimes. If there are no extra bolts then carefully pry it off.

Feb 28, 2011 | 2000 Chevrolet Silverado 1500

2 Answers

When changing the trans fluid on my 2004 Avalanche, I understand that you have to disconnect the trans lines from the radiator and run the engine until the fluid stops flowing. Is this correct? If so, do...


I didn't read about running the engine at all during the transmission fluid change. --- Removal & Installation 4L60E/4L65E To Remove:
  1. Raise and safely support the vehicle.
  2. Place a drain pan under the transmission.
  3. If equipped with a drain plug, drain the transmission fluid.
  4. If necessary, remove the bolts and position aside the range selector cable bracket for clearance while lowering the pan. It is not necessary to remove the cable from the lever or bracket.
  5. Remove the catalytic converter.
  6. Remove the oil pan bolts from the front and sides of the pan only.
  7. Loosen the rear oil pan mounting bolts about 4 turns.
  8. Lightly tap the oil pan with a rubber mallet in order to loosen the pan and allow the fluid to drain.
  9. Remove the remaining oil pan bolts.
  10. Remove the oil pan and the gasket.
  11. Remove the filter by twisting and pulling on it.
  12. Remove and discard the filter seal. The filter seal may be stuck in the pump; if necessary, carefully use pliers or another suitable tool to remove the seal.
  13. Clean the transmission and the oil pan sealing surfaces with solvent, and air dry. You must remove all traces of the old gasket material.
To Install:
  1. Coat the new filter seal with transmission fluid.
  2. Install the new filter seal into the transmission case. Tap the seal into place using a suitable size socket.
  3. Install the new filter.
  4. Install the oil pan and new gasket. Tighten the bolts alternately and evenly to 97 lb in (11 Nm).
  5. Install the catalytic converter.
  6. If previously removed, install the range selector cable bracket and bolts. Tighten the bolts to 18 lb ft (25 Nm).
  7. Apply a small amount of sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pan drain plug, if equipped.
  8. Install the oil pan drain plug, if equipped. Tighten the plug to 13 lb ft (18 Nm).
  9. Lower the vehicle.
  10. Fill the transmission to the proper level with DEXRON® III transmission fluid.
  11. Check the COLD fluid level reading for initial fill only.
  12. Inspect the oil pan gasket for leaks.
4L80E/4L85E To Remove:
  1. Raise and suitably support the vehicle.
  2. Place a drain pan under the transmission oil pan. Drain the transmission fluid and install the plug. Tighten the drain plug to 13 lb ft (18 Nm).
  3. Support the transmission with a transmission jack.
  4. Remove the transmission crossmember.
  5. Disconnect the range selector cable end from the transmission range selector lever ball stud. NOTE: It is not necessary to remove the selector cable from the bracket.
  6. Remove the transmission range selector cable bracket. Reposition the bracket and cable.
  7. Remove the oil pan bolts. NOTE: The transmission oil pan gasket is reusable. Replace as needed.
  8. Remove the oil pan and gasket.
  9. Remove the magnet from the bottom of the pan, if necessary.
  10. Remove the oil filter and neck seal.
To Install:
  1. Clean the transmission and the oil pan sealing surfaces with solvent.
  2. Install the filter neck seal and filter.
  3. Install the oil pan gasket to the pan.
  4. Install the magnet into the bottom of the pan, if necessary.
  5. Install the oil pan and bolts. Tighten the oil pan bolts to 18 lb ft (24 Nm).
  6. Install the transmission range selector cable bracket. Tighten the bolts to 18 lb ft (25 Nm).
  7. Connect the range selector cable end to the transmission range selector lever ball stud.
  8. Install the transmission crossmember. Tighten the fasteners to 70 lb ft (95 Nm).
  9. Install the transmission mount nuts. Tighten the nuts to 30 lb ft (40 Nm).
  10. Remove the transmission jack.
  11. Lower the vehicle.
  12. Fill the transmission to the proper level with DEXRON® III transmission fluid.
prev.gif next.gif

Aug 26, 2010 | 2004 Chevrolet Avalanche

1 Answer

Trying to remove oil pan from 1989 chevy 1500 350 eng to replace the gasket can you help me?


2wd Models
  1. Disconnect the negative battery cable. Drain the engine oil.
  2. Remove the oil dipstick.
  3. If necessary remove the exhaust pipe crossover.
  4. If equipped with automatic transmission, remove the converter housing pan and the transmission oil cooler line retainer from the bracket.
  5. On 1996-98 models, remove the oil filter and if equipped, the oil filter adapter.
  6. If necessary, remove the starter brace and bolt and swing the starter aside.
  7. Remove the strut rods, if equipped.
  8. Remove the oil pan and discard the gaskets.
To install:
  1. Apply a suitable sealant such as GM part number 12346192 or its equivalent to the front cover-to-block joint and to the rear crankshaft seal-to-block joint. Apply the sealant about 1 inch (25mm) in both directions from each of the four corners.
  2. Clean all gasket surfaces and use new gaskets to assemble.
  3. Install new gasket and seals.
  4. Install the oil pan.
  5. On 1988-95 models, tighten the pan bolts to 100 inch lbs. (11 Nm). Tighten the pan nuts to 17 ft. lbs. (23 Nm).
  6. On 1996-98 models, tighten the oil pan nuts and bolts to 18 ft. lbs. (25 Nm).
  7. Install the strut rods, if equipped.
  8. If removed, install starter, starter brace and bolt.
  9. If equipped, install the oil filter adapter.
  10. If removed, install the oil filter.
  11. If equipped with automatic transmission, install the converter housing pan and the transmission oil cooler line retainer to the bracket.
  12. Install the exhaust pipe crossover.
  13. Install the oil dipstick.
  14. Fill the engine with oil and check for leaks.

Aug 07, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

1 Answer

2000 chevy cavalier oil pan....2.2 lit....auto


put car on stands

remove right side engine splash shield

remove exhaust shield

remove AC brace at starter/ compressor bracket

remove flywheel inspection plate

remove engine mount strut, remove bolts from bracket. Lower the bracket slightly to gain clearance to remove pan.

remove oil filter extension (auto trans. only)

remove all pan bolts

tap pan with rubber hammer to break old gasket loose from block.

clean all used gasket off and install is reverse

Mar 13, 2009 | 2000 Chevrolet Cavalier

1 Answer

Removal of Oil pan


did you try giving it a gentle smack with a rubber hammer? these pans are usually glued on with silicone and will not just fall off after unbolting... sometimes you need to get something like a paint scraper and slide it between block and rail to seperate the two.

Jan 17, 2009 | 1996 Pontiac Grand Am

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...