Question about Toyota Cars & Trucks

Open Question

2001 toyota avalon broken wheel stud on front. How do I replace it?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: broken off wheel stud on a 1998 hyundai elantra

CLICK HERE FOR VIDEO

Thanks for using FixYa - a FixYa rating is appreciated!!

Posted on Feb 20, 2009

  • 1596 Answers

SOURCE: broken wheel stud front left 1992 honda accord

Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Posted on Mar 29, 2009

VWdan
  • 114 Answers

SOURCE: broken wheel stud

1. get new studs and nuts
2.remove wheel
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.

Posted on May 17, 2009

  • 112 Answers

SOURCE: broken stud on left front wheel

Remove: wheel, brake caliper & rotor. Drive out the remaining stub with a hammer and punch. Insert a new stud and pull it into place by tightening the lug nut. Before running out of threads, remove the nut, insert a stack of washers or a large nut which slips over the threads without contacting them, tighten the lug nut to seat the stud.

Posted on Jul 12, 2009

  • 30 Answers

SOURCE: broken stud on wheel

To replace a front wheel stud you need to remove the wheel, next remove the brake caliper. Next the brake rotor should slide off. You will need to get a punch and hammer and drive the old stud out then install new one by inserting it into the hub and using a large thick washer on the stud as a spacer thread a lug nut onto the stud and tighten to draw the stud into the hub. Reinstall brakes and wheel.

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a front wheel stud


your best bet would be to take it to the car doctor (mechanic)
or ask Hyundai as it may vary from car to car

Oct 08, 2014 | 2001 Hyundai Elantra

1 Answer

1994 4X4 TOYOTA PICKUP REPAIR FRONT LUG/STUD BROKEN


Hi, is the stud broken with the wheel on? Or is it a lug that you cannot get off? 9 times out of 10 at my shop, we use a arm hammer and or air chisel to slowely (and carefully ) break away the stud. This is time consuming but efficient.

Mar 09, 2013 | Cars & Trucks

1 Answer

After having the error code p0135 on my 2001 toyota avalon, I replaced the front sensor and am still getting a check engine light with the same code. Any ideas?


did you change the right one there is two sensor 1 o2 sensors also toyota systems a picky and after market o2 sensors will not always work right

Jul 02, 2012 | 2001 Toyota Avalon

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

We broke the lugs on our toyota echo how do we


Lugs?. I guess are the wheel studs(Im in australia)
First see if toyota sells the lugs separately, if yes you can use a punch to remove the last broken bit, the new ones are installed by packing with washers and using the wheel nut to pull them back into place.
If you cant buy lugs separately, you will need a new hub from the dismantlers

Apr 11, 2010 | 2001 Toyota Echo

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

3 Answers

Broken stud on wheel


The studs press out and in. Perhaps a hammer would work. Replacements studs can be purchased. Need to remove hub, of course.

Aug 13, 2009 | Hyundai Motor 2003 Elantra

1 Answer

2001 Toyota Avalon - Rear signals


Check the front lights. Usually if i flashes fast it indicate a bulb is out on that side.

Aug 02, 2009 | 2001 Toyota Avalon

1 Answer

Broken stud on left front wheel


Remove: wheel, brake caliper & rotor. Drive out the remaining stub with a hammer and punch. Insert a new stud and pull it into place by tightening the lug nut. Before running out of threads, remove the nut, insert a stack of washers or a large nut which slips over the threads without contacting them, tighten the lug nut to seat the stud.

Jul 12, 2009 | 2001 Pontiac Sunfire

1 Answer

Broke stud on front left side


Yes you can replace the broken wheel stud. The wheel studs are pressed into place, and a vise will work to press it out, and in. You will have to remove the wheel hub, and then use a deep well socket and a bolt or something smaller than the actual stud to remove it with a vise. To replace it, you will need to use the deep well socket on the thread side of the stud, and press the new one in with the vise.

I hope this helps you, and I wish you luck with your repair.

Apr 25, 2009 | 2003 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...