Question about Chevrolet Malibu

Open Question

How to replace spark plugs and wires on 2002 malibu

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: spark plugs and wires on a 2002 Kia Spectra

you might see a plastic cosmetic cover over the valve cover area , with like 4 screws holding it down , allen headed screws i think , you will find your wires and plugs under that cover . actually you will find 2 coils with 2 10mm bolts on each coil , each coil has a spark plug boot built on to it for 1 plug and 1 actual spark plug wire to a second plug , very short , unplug the coil connector, unbolt it and pluck it out of the hole , and see your spark plug .

J5

Posted on Jan 18, 2009

Ad
stevenhurc
  • 450 Answers

SOURCE: need wire diagram for 2002 dawoo 2.2 for spark plug wires

here

46cd27c.jpg

Posted on Jun 24, 2009

lasvegasrich
  • 65 Answers

SOURCE: replacing spark plugs on a 2004 chevy malibu

2.2L Engine

  1. Observe the following service precautions:

    Allow the engine to cool before removing the spark plugs. Attempting to remove spark plugs from a hot engine can cause the spark plugs to seize. This can damage the cylinder head threads. Clean the spark plug recess area before removing the spark plug. Failure to do so can result in engine damage due to dirt or foreign material entering the cylinder head, or in contamination of the cylinder head threads. Contaminated threads may prevent proper seating of the new spark plug. Use only the spark plugs specified for use in the vehicle. Do not install spark plugs that are either hotter or colder than those specified for the vehicle. Installing spark plugs of another type can severely damage the engine.
  2. Turn the ignition OFF .
  3. Disconnect the Electronic Ignition (EI) module harness connector.
  4. Remove the spark plugs using a 5 / 8 inch spark plug socket.

To install:

WARNING Do not coat spark plug threads with anti-seize compound. If anti-seize compound is used and spark plugs are over-torqued, damage to the cylinder head threads may result.
  1. Inspect the gap on the new spark plugs, re-gap the plugs as required. The spark plug gap specification is 42 inch. (1.0 mm).
  2. Install the spark plugs and tighten to 15 ft. lbs. (20 Nm).
  3. Apply dielectric compound to the spark plug boots and make sure no corrosion is present.
  4. Install the ignition coil housing to cam cover and attachment bolts.
  5. Tighten the ignition coil housing bolts to 89 inch. lbs. (10 Nm).
  6. Connect the EI module harness connector. Push in until a click is heard and pull back to confirm a positive engagement.

Posted on Oct 07, 2009

Testimonial: "Thanks for the help, it was easy to change out the plugs with your info."

  • 14036 Answers

SOURCE: change sparks plug wires on my 2002 yukon denaili

YOU NEED A SPARK PLUG BOOT PULLER TO REMOVE PLUGS WIRES.

Posted on Jun 30, 2010

  • 198 Answers

SOURCE: 2002 accent 1.5 no spark..replaced coil pack

hook up a scanner if you have one, check to see if your scanner is registering a crank signal.

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is causing hesitation?


Have you ever changed the fuel filter?

Dec 18, 2015 | 2002 Chevrolet Malibu

1 Answer

Why does my 2002 Chevy Malibu electrocute me while touching engine


Try replacing your spark plug wires one maybe cracked and the spark is jumping out.

Jul 14, 2014 | 2002 Chevrolet Malibu

1 Answer

My '02 chevy malibu got a code for cylinder 1 misfire. Tried replacing spark plug, plug wire, and coil pack. It smokes really bad. Black oil on spark plug. Also has a tick that has gotten worse, that...


You are getting oil in the cylinder and that is fouling your plugs. I would guess your piston rings are bad letting oil up into the combustion chamber or it is leaking down from the head through the valve guides. Good luck

Jan 07, 2018 | 2002 Chevrolet Malibu

1 Answer

I have a 2002 Chevy Malibu 3100 engine I had a bunch of error codes so I replaced the spark plugs plug wires put in a brand new EGR valve cleaned the throttle body cleaned the mass airflow unit changed the...


Use Google to look up your codes & solutions

OBD PO404

You need to study OBD2 Systems & learn to diagnose
issues & not install ANY parts until you find a problem
& component test it,that includes plug wires

Aug 22, 2013 | 2002 Chevrolet Malibu

1 Answer

My 2002 Malibu has a P0305 - what does this mean


P0305 is a Misfire on Cylinder 3 detected fault. It sounds to me like it's time to install new spark plugs and spark plug wires.

May 22, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

It has lost power when i push on the gas pedal. i


it could be the plug wire doing this.or the coil, change plug wire to see. if a little better, change or check fuel filter also.

May 25, 2010 | 2002 Chevrolet Malibu

1 Answer

2002 Chevrolet Malibu. Replaced fuel pump after diagnosis


Sounds like a leaking fuel pressure regulator. After it has been replaced change the oil and check for oil leaks.

Oct 30, 2009 | 2002 Chevrolet Malibu

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

2000 Chevy Malibu Hesitaiton when gas get s less than 1/4 tank


I would say do a tune up like spark plugs and spark plug wires.

Sep 10, 2009 | 2000 Chevrolet Malibu

1 Answer

2002 chevy siliverado will turn over, but will not start


Check the fuel pressure when it won't start also check for spark when it is not starting

Mar 08, 2009 | 2002 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...