Question about Cars & Trucks

Open Question

Codes po562 po700 and p1603 present on my 2006 pt chrysler

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: cI have a chrysler 300m

You don't replace a transmission
Worse case you remove and rebuild

Go to a trans repair shop for a road test
and diagnoses

Posted on Jan 30, 2011

jgwhomeequip
  • 1902 Answers

SOURCE: 2002 Pt cuiser code# po605 & po700

the 605 is an internal Tranny computer failure U will need a tranny computer no way around it. It will also need to be programed as well once installed.

p0700 also has to do with the transmission

Posted on Jun 25, 2011

saa_aa
  • 241 Answers

SOURCE: how to fix Chrysler 300M: 99 30m Chrysler have the codes po700,po734,po733,po122,po113,po108

I would like to ask you that did you change the Transmission .

Posted on Nov 24, 2011

chargerhp
  • 813 Answers

SOURCE: Chrysler 300M: 99 30m Chrysler have the codes po700,po734,po733,po122,po113,po108

108 Map sensor or pcm computer,113 IAT sensor or pcm,122 TP sensor or pcm, 700 Automatic trans computer or pcm, 733 Automatic trans leak or low pressure, 733 leak low pressure Your main computer(pcm) is shot start there. Then possible trans computer shot also(TCM)

Posted on Dec 18, 2011

  • 7 Answers

SOURCE: DODGE CARAVAN 2007 AND CODE

I just had the same codes a week ago. P0562 & p0700. Found that they were both related to a battery with a dead cell. The p0562 (low voltage code caused by no good battery) causes the transmission control module (p0700) to not receive the correct voltage and act up when drawing power from the battery due to dashboard, starter, etc. drawing from battery as well, With the keys in the ignition. I changed the battery to a new one. Removing the battery will reset the codes and with the new battery the codes may not re-appear, provided there are no other codes pending that could be causing the p0700 code. Some conditions you may experience are 1) no start 2) clicking from the tcm 3) clicking from the starter 4) the dashboard lighting having a life of its own coming on and off, dimming, etc. note: when this happened to me (all of the above) I tested the battery and it was ok, but the problem existed until the New battery was installed. Still runs good now

Posted on Jul 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Pacifica touring and the following error codes: po700, po562, po736; po732, po731 and po,720 and po480. Can you tell me what I need to fix this?


With that many codes and those specific codes I would suggest finding a reputable transmission shop. I suspect either a wiring issue or a bad trtransmission control module. A good shop should be able to determine which in just a couple hours or so.

Oct 27, 2016 | 2006 Chrysler Pacifica Touring

1 Answer

Dodge 2002 stratus 2.4liter codes po016 p0700 ,po562,what could these mean & how do you fix


lets start with po562, this is a transmission code with low voltage reading at trans solenoids, for this code test your battery and alternator,
the next code po700, this code is to tell you that there is a transmission code stored in the transmission module, which could be the po700. but sccanning the trans module may be a good idea to check for other codes, i assume at this point you are having transmission problems? as far as these codes i would check all fuses and connectors going to transaxle(transmission). you may have internal problems, as we know these chrysler transmissions are junk but you may have bad connection or bad wire to transaxle controller.
last code po016 this code i would check first, i have worked on a few of these that had po016 which means crank and cam correlation . this means the crank and cam are not aligned meaning worn chain , these 2.7 engine... or cam gear spun. testing this ,you will need to know about car repair or you could damage the engine if it isnt already.

May 08, 2013 | Cars & Trucks

2 Answers

My 2004 chrysler concorde throws codes po562 and po700 and will not start unless i have my battery charger plugged up to it. What could this be?


get a good battery into it and you should be fine. I don't remember where they hid the batteries on that one, but if it's in front of the left front wheel you will need to clean the contacts and test your battery because that configuration was problematic.

Mar 03, 2013 | 2004 Chrysler Concorde

1 Answer

Pls my 2006 Chrysler PT cruiser shows error codes: po622, po700& po880. What do I do?


alternator asking for new one[good should read 14.5V.po622. po700 could be erorr or trani. filter.

Jan 27, 2013 | 2006 Chrysler PT Cruiser

1 Answer

CHECK ENGINE LIGHT IS ON WITH 3 CODES


It is the alternator pull out the old one autozone taste it. Pass the test alt good amp volt gives rong volts when you press gass rpm go up3600 volts droop from 14.7 to 10.5 to lowest 8 because alt cylinder is bad 3 codes 1 overall 2 and3 sands low volt codes to the brain you will. Thanks me

Oct 08, 2012 | 2005 Chrysler PT Cruiser

1 Answer

P0700/p1603/p1604/po613


fco.lozano, mi carro cirrus 2005 lxi turbo 2.4 triptoni, a veces no entra la tercera c bloquea y nada mas entra segunda lo apago cuando ya esta medio frio lo enciendo y entran bien las velocidades pero c vuelve a calentar pasa lo mismo kien me puede ayudar xfa. gracias

Jul 18, 2012 | 2003 Chrysler PT Cruiser

2 Answers

Can you tell me what the codes PO605 and PO700 are? PT Cruiser 2001


P0605-------- Internal control module read only memory (ROM) Error
Have the computor checked.
P0700-------- Transmission control system
Better take it to a transmission shop and have that checked so they can pinpoint the problem.

Aug 27, 2011 | 2001 Chrysler PT Cruiser

1 Answer

2002 Pt cuiser code# po605 & po700


the 605 is an internal Tranny computer failure U will need a tranny computer no way around it. It will also need to be programed as well once installed.

p0700 also has to do with the transmission

Jun 25, 2011 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

Codes under P0700 are P0765 and P0760, do this require transmission replacment or can they be isolated and repaired this is for a 2001 pt cruiser, automactic trans with overdrive.


hi checking your spec po700 is your transmission switch carnt find po760 the computer is telling you its a problem with the switch only hope this is helpfull if so please rate it thanks

Nov 21, 2009 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...