Question about 1987 Ford F 150

1 Answer

How do I remove the power steering in a 1987 f 150 truck 6 cyl 4.

I can't remove the power steering pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

You will need a special tool to remove the pulley first. You will be able to get it out after that. Some parts companies will loan tools or you can purchase them.

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheres the power steering resivior in a 89 astrovan


Either 6 or 4 cyl should be right front of the engine where the fan belt is as part of the power steering pump
0900c152800a84c1.jpg

Feb 17, 2012 | 1989 Chevrolet Astro Cargo

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

Serpintine belt diagram


what engine? Please rate if it helps

3.L v6

snorkelbobby_26.gif Item Part Number Description 1 3A733 Power steering pump pulley 2 8620 Drive belt 3 2E884 A/C clutch pulley 4 6316 Crankshaft pulley 5 6B209 Drive belt tensioner 6 10344 Generator pulley


2.0L Zetec 4 cyl with A/C

snorkelbobby_27.gif Item Part Number Description 1 10344 Generator pulley 2 19A216 Belt idler pulley 3 3A733 Power steering pump pulley 4 6C301 Drive belt 5 2E884 A/C clutch pulley 6 6B320 Crankshaft pulley 7 8509 Water pump pulley 8 6A228 Drive belt tensioner

Jan 12, 2011 | 2002 Ford Escape

1 Answer

How do i change the power steering pump belt on my 2003 mitsubishi galnt 4 cyl . ?


on the left side of motor is the power steering pump to the right is a bolt head (14mm) turn it counterclockwise until the belt is loose enough to remove. reverse proceedure to replace

Dec 18, 2010 | 2003 Mitsubishi Galant

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

How do you replace a serpentine belt on a mazda 626


A 626 has two belts. One drives the power steering and water pump (rear belt in 6 cyl) and other front belt drives the a/c and alternator. On the 4 cyl, the front belt drives the power steering and the a/c, and the rear belt drives the water pump and the alternator. All of these are easy to change.

Jul 04, 2009 | 2003 Mazda Protege

1 Answer

Power pump leaking. Removed pump, want to remove pulley


This requires a special tool; you may be able to rent it

May 22, 2009 | 1994 Plymouth Voyager

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...