Question about 1999 Ford Ranger SuperCab

1 Answer

Clutch wont let gears go in..

The clutch is soft and wont disengage to let the gears go in when the truck is on.it has been blead and it seems like there is not air anymore,so i was wondering what the problem was?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 3,433 Answers

Was the clutch replaced?
Have you verified release travel?
open slave cylyder andv remove clutch fluid master cykider cover. permit gravity bleed untill fluid constantly drips, then close and refill. No pedal pump needed. let gravity bleed.

Posted on May 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 mini one wont go in gear whilst engine running, clutch seems perfect never slipped low bite, brutal force required to try engage and still wont go in


this indicates that the clutch plate is not properly disengaged with he foot on the pedal
If it is hydraulic I would be checking for air in the system of faulty master cylinder
More costly problems may be oil grease on the clutch linings causing it to stick or drag, spigot bearing in the rear of the crank shaft seizing up, rust or dry grease and dust on the splines of the input shaft preventing the clutch plate from moving
All or any of these require a box removal to fix
if clutch is cable operated then the cable may be failing and stretched resulting in the clutch not disengaging properly

Apr 01, 2015 | Mini One Cars & Trucks

1 Answer

Manual clutch replacement


the clutch going to the floor and not going into gear sounds like the clutch wont disengage . could be lugging the engine down. could be low fluid or fluid leak or bad slave cylinder or clutch master cylinder

Oct 04, 2013 | Chevrolet Cobalt Cars & Trucks

1 Answer

2000 ford zx2 shift for issues


Can you verify that when you push the clutch pedal to the floor the slave cylinder is moving the pin that goes between the slave cylinder and the clutch fork. It sounds like the clutch is not releasing properly.

Apr 07, 2017 | Ford ZX2 Cars & Trucks

1 Answer

Soft clutch pedal


After speaking to my mechanic I blead the clutch out. It was full of air, now seems to be back to normal. This is the easyest place to start.

Apr 11, 2012 | 2003 Oldsmobile Alero

1 Answer

Crank no start will run if clutch is dumped


If clutch is dumped? do you mean if clutch is pumped? perhaps the slave cylinder for the clutch is leaking, causing low on fuid. Check level, blead if necessary. Most have vehicles must have clutch depressed to start vehicle. If the clutch pedal is not disengageing the clutch, it wouldn'tn start.

Jul 18, 2010 | 1995 Volkswagen Jetta

1 Answer

1990 300 zx installed slave and master clutch cylinders,bleaded,and still clutch wont work


The master is bad,or the clutch is worn out,If the clutch will not disengage so you can move the shifter ,then the master for the clutch is bad,but if it just does not pull the vehicle,then the clutch needs replacing.

May 24, 2010 | 1992 Nissan 300ZX

3 Answers

My truck is a manual and it wont go into gear after cranking it up. The petal is soft and easy to push to the floor. We have put a clutch cylinder and a slave cylinder and have bleed them. and it still...


It could be a bad clutch cylinder or a bad slave cylinder. If it is either - the clutch would not fully disengage. This would make changing gears very difficult. If it is the slave cylinder the system should loose fluid and start to drip if you pump it repeatedly. If it is the clucth cylinder it should just seep past the plunger seals and the fluid may not lower. If you put the truck in gear without starting it and push the clutch in - can you push the vehicle? If the answer is no - the clutch is not fully disengaged.

Jan 26, 2010 | 2003 Honda Element

2 Answers

Clutch problem - battel to get gear lever in to gear


Well cindy for what i read from your question it just sounds to me to be the slave cyl. or master cyl. i got to admit i don't know exzactly what your set up is, but most have a resavor under hood with a line running down to a slave cyl. witch in turn pushes clutch to disengage clutch, now that slave cyl. can bleed off with very little sign of leakage, and from my experance from other cars and trucks thats where the problem lies is in the slave cyl. or what you understand is master cyl.

Mar 02, 2009 | Ford Festiva Cars & Trucks

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...