Question about 1995 Mercury Villager

1 Answer

The linkage is sliping falles out of gear wont go back up to reverse.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

The 2 screws on the steering column under the dash are loose.

go here and see photo on loose shifter.

http://groups.yahoo.com/group/villagerquest/

Posted on Sep 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my 1986 f250 auto ****** not go into rev. or park


it sounds like you reconnected the linkage in the wrong position so it can still go into the forward gears but there is not enough cable length to allow for reverse and park to be engaged disconnect the linkage again and use trial and error to get it back to where you need it also the linkage should show you where the bolt was that tightened it but if you took it off and then moved either the linkage or the transmission gear selector arm on the transmission now its not in the position it was when you disconnected it resulting in this problem of no access to the other shifter points park reverse and you will have to check all gear shifts till you get it right but if it was in park when you took it off take the linkage off move the trans gear selector to park and reconnect it where the old marks are and you should be O.K.LATER MAN!

Aug 21, 2014 | Cars & Trucks

1 Answer

I tried to put my 2003 Trailblazer in drive but the handle moves but will not go into gear what is the problem?


if you feel the handle clicking into gear (you feel it distinctly fall into place in reverse, neutral, and drive) but it wont go, it might be the electronics, or it could be a bad transmission. if this problem just happened one day with no warnings of the transmission going out, its probably the electronics. however if the handle feels like its just moving up and down without falling into place, its probably the transmission linkage. should be quick and cheap in that case

Oct 20, 2012 | 2003 Chevrolet TrailBlazer

2 Answers

Cannot get 5th and reverse gear. Feels like neutral. 1, 2, 3 and 4 work fine.


the linkage is loose or poping out! check to c if trans is tightend down

Aug 22, 2012 | 1995 Dodge Neon

1 Answer

91 dodge with 318 will not go into reverse


it could be the linkage is bent or slipped a little on the drivers side under the car find the cable linkage look and see if the screw has slipped if it has move it back and tighten it up

Aug 21, 2012 | Dodge D150 Cars & Trucks

3 Answers

Drives okay in 2 gear but if I put it into drive is revs like neutral after 2nd gear 2000 sunfire 2.2 auto


You might check your transmission fluid level... but I'm thinking it is more serious than that.

Oct 30, 2009 | 2001 Pontiac Sunfire

1 Answer

Manual transmission will not reverse


check under car at shift linkage may need adjustment or loose

Oct 06, 2009 | 1995 Chevrolet Camaro

1 Answer

Gear linkage loose so wont stay in park, car rolls


loosen up the linkage at the transmission a little,click the linkage i click on the transmission(shift it manually to reverse),put the gear selector in the car in reverse,then tighten the linkage.see if that helps.

Apr 26, 2009 | Ford Taurus Cars & Trucks

1 Answer

My 1996 mercury mystique wont go into reverse


not a frozen linkage....the cable could be stretched but you should be able to putit in a different gear and get reverse if that is the case..it my have messed up the transmission as well. take it to a shop and find out what they have to say

Feb 01, 2009 | 1995 Mercury Mystique

1 Answer

1996 mercury cougar xr7 shifting problems


Does it go into park? The linkage might be sliping on the tranny

Jan 10, 2009 | 1996 Mercury Cougar XR7

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...