Question about 1998 Dodge Ram 1500 4WD

1 Answer

Axle Seals I'm tight on cash and need my front axle seals replaced, I was wondering how long it would take to replace the seals on a dana 44f front axle.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers

Book time is a little over 6 hours to do both. if its your first time count on it taking a lot longer

Posted on May 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have gear oil leaks under transmission in two holes next where the axel meets on each side

Keith the seals will need replaced, take into a shop and have a tech give estimate for repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
half shaft seal replacement Google Search
How To Install Replace Front CV Axle Shaft 2002 09 GMC Envoy and XL XUV
Part 1 How To Replace Front Axle Shaft Seal RH Front Chevy GMC
CV axle replacement Subaru Outback 2000 Legacy Forester Install Remove...

May 04, 2016 | Cars & Trucks

1 Answer

What are some tips on removing and replacing brake lines etc when replacing the rear end on 97 Dodge 1500

Held on by a bolt and two clips. Bend the clips and remove the bolt. Just be prepared to replace them if they are really rusty. If it were mine, I would pull the axles, Replace the diff and pinion and seal. Replace the axle bearings and seals, if the seals were leaking. If not leaking, just replace the seals.

Mar 06, 2016 | Dodge Cars & Trucks

1 Answer

Replacing front axle seals and bearings

I replaced the left front bearings and seals a couple of months back. It is not a problem but be careful as you dismantle the system and of course the reassembly of same. Be sure to replace all bearings and seals as you probably don't want to do this job twice at the cost of parts. No special tricks and relatively easy job. 1601d678-bcb0-4cc6-af13-c2a57bf7d073.jpg

Jun 22, 2014 | 2001 Ford F-250 Super Duty

1 Answer


The diff is part of the trans axle automatic transmission assembly and is not a separate part that can be removed.

Oct 10, 2012 | Cars & Trucks

1 Answer

How do i replace the axle seals on my 69 roadrunner. it has the dana 8.75 rear end. it is leaking the gear oil into my brake drums

first make sure that its not the wheel cylinder's causing the leak as well okay? if so, replace. thats pretty straight forward. If it is for sure the axle seals, then you will need to remove the brake drums. take off the differential cover. there should be like 13 bolts, empty out the fluid. Rotate the differential carrier unti you can see a small bolt. remove the bolt and take out the axle pin. Once the axle pin is out, then push ONE axle in until u hear something drop. this is a c clip that drops inside housing usually will land at the bottom in the remaining oil. pick out clip. keep off to the side as u will need to reinstall this clip later. then once clip is out pull axle out of tube, and set aside. there are multiple ways to remove the seal itself. you can use a seal puller, screw driver, pry bar, or the axle itself. Becareful not to scratch the bore where the seal goes or else IT WILL LEAK. then just do the same for the other side. pay attention for the bearings and not to nick them either, or else they will need to be replaced as well and that's much more of a pain in te ***, lol..good luck!

Aug 24, 2010 | Plymouth Scamp Cars & Trucks

1 Answer

Dana 60 axle seals replacement

changing pinion seal on 79ford e-250 dana60.are there any cautions or recommendations concerning torque or preload.

Dec 19, 2009 | 2006 Ford F-250 Super Duty

1 Answer

I just replaced the axle shaft seals in th e rear

When you say you can hear the bearings, I wonder what you are hearing. If it only started from doing the seals, I would go back in and see if something is rubbing. Bearings don't go bad quickly.

Jul 05, 2009 | 1989 Suzuki Samurai

1 Answer

2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

1 Answer

I think the front axle seals on my 1999 dodge 3500 4x4 need to be replaced. I am replacing the sealed bearing hubs and I wonder how big of a job it would be to switch out the axle seals inside the...

if you have the hubs of than you dont have much futher to go to replace the axl seals. just slide out the axls the passenger side is two pice then take out the four bolts that hold in the carrier gear then pull out the hole gear asemblie the driver side seal is in the differential housing the passenger seal you have to take of the cad unit in the middle of passenger side axle article with pictures at pavement

Jun 28, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

698 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides