Question about 2006 Pontiac G6

1 Answer

Blend door motor actuator removal

How do i get to the temp.control actuator on a 06 pontiac g6

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 155 Answers

It's located on the left side of the HVAC case under the dash, about halfway up the case. On the drivers side, close to the side of the center console.

Posted on Dec 29, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blubanshee
  • 48 Answers

SOURCE: need to remove door panel on a pontiac g6 to

I found a great write up on your door panel I think will help you out allot Click Here Its a great sight for any G6 owner. If this was helpful please dont forget to rate me.

Thanks and have a great evening

Posted on Jun 11, 2009

polarcycle
  • 1392 Answers

SOURCE: how to remove interrior door panel pontiac G6 and replace broken

Remove any bolts/screws you can see then get a plastic crowbar and pry it off. Should have little plastic push pins holding it to door. Make sure you remove all screws though.

Posted on Mar 06, 2009

  • 1 Answer

SOURCE: how to remove door panel 2008 pontiac g6

2008 g6 sedan i want to remove drivers door panel?Curt.

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: 2006 Pontiac G6 GTP window auto close/open

OMG. I replaced the battery in my 06 G6 and had the same problem. the windows would not roll up or down how they did before. I read the answers on here and it does work. Hold up the window switch for ten seconds and it resets. You will have to do it to each window. Worked great. Thanks

Posted on Jan 18, 2010

  • 880 Answers

SOURCE: how do I expose the motor on a 2006 pontiac g6 to

Remove everything from the headliner and remove all of the trim holding it in place. Carefully pry the headliner out from one side and the rest will now be easily removed. Unless the car has been subject to abuse and intense heat the headliner will not come loose from the backing and can be reinstalled.

Posted on Mar 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

My 2007 Pontiac g6 blows cold air in heat mode. Coolant level is okay


Possible blend door motor inoperative or restricted heater core. Once engine is at operating temperature feel the two hoses going into the heater core. They should be close to the same temperature. If one is hot and one is warm/cold, the heater core is restricted. If both close to the same temp suspect an inoperative blend door motor that controls airflow/heat inside the car

Dec 21, 2015 | Pontiac Cars & Trucks

1 Answer

Where is the blend door actuator located on 07 g6


Did you resolve your issue? I have the same problem, believe the blend door is jammed on my 2006 Pontiac G6. Please help!

Jan 26, 2013 | 2007 Pontiac G6

2 Answers

Heater blows cold air


Hi!
If the Temp. Selector Control is set to Heat and blows cold air, your Blend Door Actuator may be stuck or it is inoperative. The actuator is not fixable, if it fails, it must be replaced. Follow the instructions to remove and replace it.
  1. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.
  2. Remove the instrument panel.
  3. Disconnect the electrical connector from the blend door motor/actuator.
  4. Remove the four screws holding the blend door actuator to the plenum.
  5. Remove the temperature blend door actuator.
BLEND DOOR ACTUATOR CONNECTOR e8349ea.jpg

BLEND DOOR FASTENING SCREWS 9744710.jpg

Show your appreciation with a - 4 THUMBS - rating for answering your FREE question. Thank you for using FixYa.

Oct 07, 2010 | 2003 Mercury Grand Marquis

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

1 Answer

My air conditioner is working but won't blow out


Are you saying the temp blend door is not working?
If yes, it's the control head or the temp blend door motor on th plenum case under the dash. Buy used on ebay.

DO you have manaul or electroic controls?

If electronic

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on top of the A/C evaporator core housing (19A553) assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A five volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
-----------------------------------------------------------
manual

#3 is the blend door.

0425af0.gif

May 08, 2010 | 1998 Mercury Grand Marquis

1 Answer

My heater will only blow hot air out of the rear vents from the rear controls. The front vents only blow cold air. Is there a simple fix?


blend door or temp contrl switch is bad.

Section 12-02: Heating and Defrosting 1998 Windstar Workshop Manual
REMOVAL AND INSTALLATION Actuator Motors, Electric Temperature Blend Door
Removal
  1. Remove cassette storage box or center shelf unit, if equipped.
  1. Remove instrument panel ash receptacle (04810) by depressing service lever.
  1. Disconnect electrical harness connector from electric blend door actuator.


    sww~us~en~file=am0101a.gif~gen~ref.gif

  1. Remove three retaining screws.


    sww~us~en~file=am0100a.gif~gen~ref.gif

  1. Carefully pull electric blend door actuator outward and off A/C evaporator housing (19850) assembly.
Installation
  1. Follow removal procedure in reverse order.
  1. Air temperature control door shaft is keyed. Move door to properly insert electronic actuator shaft. Make sure the shaft is completely in and properly seated.

Jan 14, 2010 | Ford Windstar Cars & Trucks

1 Answer

I have to replace the ac door actuator motor behind the ash tray


are you sure it is not the temp control on the heater control panel that's bad?
please rate if this solves your issue.

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on the rear of the A/C evaporator housing assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A 5 volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and is matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
A/C Electronic Blend Door Actuator
Removal
  1. Disengage two push pins retaining instrument panel insulator to instrument panel. Disconnect courtesy lamp from instrument panel insulator.
    1. Remove floor console. Refer to Section 01-12 .
    1. Working from under instrument panel, remove two retaining screws and metal cover from A/C evaporator housing.
    1. Remove A/C electronic blend door actuator electrical connector.
    1. Remove three remaining retaining screws from A/C electronic blend door actuator.
    1. Pull the A/C electronic blend door actuator away from the A/C evaporator housing for a distance of approximately 25 mm (1 inch) to disengage it from the A/C air temperature control door.
5728f0a.gif

May 24, 2009 | 1997 Lincoln Continental

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2006 Pontiac G6 Logo

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...