Question about 2005 Pontiac G6

1 Answer

Replacing the starter

Starter motor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Is there a speed sensor located internally in a 2005 pontiac G6 transmission? I have already changed the speed sensor behind and below the alternator. Will not shift out of low gear.

Posted on Dec 30, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing starrter


the solenoid is part of the starter normally although some early delco made starters simply spun the motor and the action threw the starter pinion into the ring gear to start the motor
I believe that on your vehicle the solenoid is part of the starter motor

Feb 20, 2015 | Dodge Ram 1500 Cars & Trucks

1 Answer

Oldsmoblie intrigue where is the starter relay at


Most starter relays are part of the starter motor assembly.
Also known as the solenoid.
(This way it serves 3 purposes.
1. The Relay section uses solid copper Contacts for Less volt drop at the high current that a starter motor draws.
2. The Solenoid section is the Mechanical Plunger that engages the cog to flywheel.
3. The Motor spins because the copper contacts are a super connection supplying 100+ Amps)

Does the battery go direct to the Starter Mptor?
Is there a small wire next to where the Battery connects?
If so then this is the relay activation wire (12v to pull relay in)

Happy Starting

External Relay Basics
Same but bigger for Starter Motors
RELAY BASICS

Starter Solenoid - A Gutsy Relay
Testing and replacing pre engaged starter motor solenoid
How To Test Car Starter With Screwdriver And Jumper Cables

Oct 03, 2014 | 1998 Oldsmobile Intrigue

1 Answer

Starter wont engage after replacing dead battery


Check power to starter motor solenoid, solenoid operation and starter motor voltage during cranking. If the starter motor is receiving power from the solenoid, but isn't cranking, then replace the starter motor.

Also check the condition of battery terminals, wiring and connections. Also check the earth wire from the body to the engine.

Nov 12, 2012 | Cars & Trucks

2 Answers

My car is making a whinning noise when i try to start it and i won't start


Can you tell if the engine is actually turning over? My first thought would be that the bolts holding your starter on the engine have loosened and the starter is not making contact with the flywheel. Another possibility would be that the flywheel has lost some teeth. Safely jack up the car and see first if the starter motor is loose, if not, open the inspection plate under the flywheel and get a visual look at where the starter and flywheel come together. If neither seem to be happening, then the starter itself may need replacing.

Mar 04, 2011 | 1991 Oldsmobile Cutlass Ciera

1 Answer

What would be the problem with our toyota 4runner starter motor that when we turn the key the starter motor just makes a grinding noise, is it the starter motor or something else??


The grinding noise is the starter hitting the fly wheel. This means that the starter is spinning but may not be engaging all the way. Your Flywheel is probably missing a few teeth now. I recommend replacing starter and flywheel. If you're on a tight budget then you could just replace the starter but it will cost you more in the long run.

Dec 05, 2010 | 1991 Toyota 4Runner

1 Answer

Can u show graphic for replacing starter motor


I can't show graphics but I can tell you how, firstly locate the starter motor, remove the battery lead from the starter motor,plus the small lead from the solenoid then remove the bolts that secure the starter motor,pull the starter motor out, replacing is the reverse.....hope this helps....cheers

Jul 19, 2010 | 1998 Subaru Legacy

1 Answer

I need instructions on how to put a new starter 97 jetta GLX


You may want to check some things out before actually replacing the starter.

Check the fuse in the fuse box and the relay.

There are two parts to the starter. One is the actual starter motor and the other in the starter solenoid. The solenoid moves the starter motor into place and engages it into the engine.

When you turn the key you should hear the solenoid click as it moves the starter. If you hear the click and the sound of the stater motor spinning it is just the solenoid. It can be replaced without replacing the starter motor.

If you hear the click and no sound of the starter motor trying to turn. It is the starter motor.

It check for power at the motor. Use a test light or voltage meter to see it is getting power when the key is turned.

If you are getting power you have a problem with the starter motor as you suspect already. The above may save you money.

To change the motor it is fairly simple to do. You remove the four bolts holding the motor in place, remove the electrical connections. Slide the motor out. Installation is the reverse of removal.

I am assuming you know where the starter is. On a diesel it is on the back of the engine. On a gas engine it is on the front side.

If you really want to get into it you can replace the brushes on the starter motor. Once out you open the starter and install new brushes it they appear warn and are not making contact.

If you need details I would go to the library and ask for the Bentley service manual. They will have one or can get one from another branch.

Hope this helps.

Mar 07, 2010 | 1997 Volkswagen Jetta

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

How do i remove starter on 2001 ford f350 dually (7.3 l powerstroke)


Starter

Removal & Installation 1. Disconnect the positive and negative battery cables.
2. Raise and safely support the vehicle.
3. Remove the starter terminal cover.
4. Remove the terminal nut and separate the battery starter cable from the starter motor.
5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.
6. Remove the starter motor retaining bolts.
7. Remove the starter motor from the vehicle.
To Install:
8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).
9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).
10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
11. Install the starter solenoid safety cap. If equipped.
12. Lower the vehicle.
13. Connect the positive and negative battery cables.
14. Start the engine several times to check starter motor operation

May 27, 2009 | 2001 Ford F350 Super Duty SuperCab

2 Answers

Replacing a starter


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.
0900c152800b83b4.jpgFig. 2: Use a ratchet and socket extension to loosen ... 0900c152800b83b5.jpgFig. 3: ... then remove the starter mounting bolts
  1. Making sure the note their positions, detach the electrical leads from the starter motor.
0900c152800b83b6.jpgFig. 4: Loosen the retainers, then remove the wiring from the starter
  1. Remove the starter motor from the vehicle.
0900c152800b83b7.jpgFig. 5: Carefully lower the starter motor from the vehicleTo install:
Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cable to 11 ft. lbs. (15 Nm).5c28dd1.jpge527647.jpge29ea94.jpgec5c533.jpg

Oct 06, 2008 | 1993 Chevrolet Camaro

Not finding what you are looking for?
2005 Pontiac G6 Logo

685 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...