Question about Cars & Trucks

Open Question

How to change a 2008 nissan quest blower resistor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: AC blower motor resistor Nissan Maxima 2000

yeh its located under the passenger side glove box,its in the heater box beside the heater motor ,,2 scews hold it in and it looks like a credit card when its out,,,,

Posted on Apr 19, 2009

cj2176
  • 520 Answers

SOURCE: Where is the blower resistor on a 2001 Nissan Sentra?

Its actually not that bad to change. If you open the glove box and remove the screws then the screws along the bottom of the glove box at the bottom of the dash the box will slide out. Remember to disconnect the light if it has one. Now you will be able to see the underside of the dash. You can see a large black box that has wires and vacuum lines all over. You need to locate a small flat plate with two screws and a plug in the middle. Disconnect the plug and remove the screws. The resistor will come straight out. The back side will look like small coiled up springs of different sizes. Install in reverse.Hope this helps. Good luck. Please re-post with updates. Thanks cj2176.

Posted on Jul 13, 2009

  • 126 Answers

SOURCE: Where is the blower motor resistor located on a

most are on the heater case near the blower motor

Posted on Oct 11, 2009

emissionwiz
  • 75817 Answers

SOURCE: Where is the blower resistor located on a 2008

The blower control module also known as the blower motor resistor is on the passenger side of the firewall in the engine compartment near the blower

05b686d.png

Posted on Nov 12, 2009

Testimonial: "Thank you! You saved me hours of searching under the dash for something that was under the hood! Thanks again. Bill"

mpurai
  • 14 Answers

SOURCE: Does the nissan quest 1999 timing belt needs to be

The Quest has a non interference engine meaning that should the belt break the engine would just die without breaking anything. Nissan recommends 105K for changing but that depends on the way the vehicle was driven (driving habits), road conditions etc. If driving on roads for e.g. that are hilly, it labors the engine more thus shortens the lifespan of the belt according to mfg.

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Nissan Quest My fan works on high all the


The resistor limits power to the blower to make for the slower speeds. It could be a sticking fan relay or the controller.

Aug 12, 2013 | 2002 Nissan Sentra

1 Answer

I can't seem to locate the blower motor resistor for my 2005 Nissan quest.can you help me?


normally in the blower motor enclosure as it uses air flow to help cool the resistors

Mar 23, 2013 | Cars & Trucks

1 Answer

Nissan quest 2005 SE rear blower motor heat is in high speed i put a new resistor and still same problem


NISSAN QUEST 2005 SE ,FRONT BLOWER RUNS AT HIGH SPEED ON HEAT/AC,EVEN WHEN THE LED INDICATORS SHOWS DIFFERENT SPEED

Mar 18, 2013 | Cars & Trucks

1 Answer

Where is the blower resistor for a 2007 Nissan quest


usually bolted to the firewall close to the motor .

Mar 12, 2012 | 2007 Nissan Quest 3.5 Minivan

1 Answer

2001 Quest: I own a 2001 Nissan Quest. About a year ago I took...


you have a bad blower motor. It is drawing too much current causing the resistor to go.

The other problem is your spark plug wires have bad insulation. Change them with at least 8mm diameter wires.
Ignore knock sensor code, it is responding to misfire.

http://groups.yahoo.com/group/villagerquest/

May 17, 2010 | 2001 Nissan Quest

2 Answers

2001 nissan quest front blower does not work on two lowest speeds.


Change your blower motor Resistor...it's probaly oxidized on those two coils....

Dec 04, 2009 | 2001 Nissan Quest

1 Answer

1996 nissan quest blower wont work. checked


There might be some heavy resistance with one of the wires leading to it. Have an electrician check it out.

Jul 14, 2009 | 2002 Nissan Pathfinder

2 Answers

Blower is working on position 4 (max) only


The fan speed control resistor is burned out.

Nov 23, 2008 | 2000 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...