2001 Chrysler 300M Logo

Related Topics:

A
Anonymous Posted on Dec 28, 2013

2001 chrysler 300m front fascia removal - 2001 Chrysler 300M

5 Related Answers

Anonymous

  • 4 Answers
  • Posted on Aug 05, 2009

SOURCE: my 2001 Chrysler 300m idles very high and will not

Either a cracked plenum or bad plenum gasket.

Ad

Anonymous

  • 1986 Answers
  • Posted on Sep 14, 2009

SOURCE: how can i remove the door panel from right front

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.
It sounds like the rod connecting the latch to the interior handle has disconnected or broken

Anonymous

  • 381 Answers
  • Posted on Mar 29, 2010

SOURCE: how do you remove the rear seat in a chrysler 300M

Grab the bottom seat cushion at the front of one side and pull it straight up then do the same on the other side. (you will have to pull up very hard) The bottom of the seat clips in. once you have the bottom out take the 2 bolts out of the seat belt fasteners that holds the bottom of the top seat cushion. Then pull straight up on the seat cushion to slide it off two tabs that hold the top.

Anonymous

  • 2 Answers
  • Posted on Sep 29, 2010

SOURCE: 2001 Chrysler 300M Engine Light on all the time

Hello, my engine light was on for a VERY LONG time and everytime I got it checked no one could tell me what the problem was because things always checked out fine. The "code" says its a loose gas cap or something, but it wasnt that. My 300M also was having A HARD TIME STARTING UP for about 8 months and leaking coolant for about a month. I finally found a mechanic who knew what he was doing; 1. Leaking Radiator 2. Coolant found in #2 or #3 cylinder. The cause of this was a busted HEAD GASKET. If your 300M has trouble starting and the Engine light stays on have a mechanic check your engine for a busted head gasket and see if all your cylinders are firing correctly. I had to pay $2600 for a new Head Gasket, Radiator and all new hoses plus labor. CRYING!!!!!!!!!!

I have a 2001 300M 130K - very well kept. Stuff happens...

Testimonial: "2001 300m max price $6000 -$2000 to much money for repair I have had a loose gas cap engine light on the on disconnected the.batt ok now reboot"

Anonymous

  • 1 Answer
  • Posted on Nov 25, 2010

SOURCE: 2001 chrysler 300m radio flashes and has power but

You may have a short in the radio. I just went through this with my 2002 300M (caused by a dead battery..low voltage can cause this to happen). Spent $60 at Dealer today for them to tell me I need a new radio for $300 plus install. I found a brand new one at primelec.com for $24.99 Only 4 screws to install it, but be careful removing the surrounding face place as only pressure hooks holding it in place.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

I own a 2001 Chrysler 300M and the drivers side window will only work sometimes? What would make this happen?

It could be the groves on the regulator that have been worn down so it is not catching correctly. If you remove the door panel you should be able to shine a light into the door to see it the grooves have any tread left.
0helpful
1answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.
0helpful
1answer

How to replace the a/c belt on a 2001 chrysler 300M

you need to remove upper radiator core support set on engine loosen 15mm bolt on front of alternator tensioner and 13mm bolt behind the tensioner pulley remove this belt then go under passenger front and you will see the tensioner bolt for the ac belt turn until tension is released remove belt replace belt and reverse instructions to put back together
0helpful
1answer

How do you remove the air filter box on a 2001

REMOVAL
Release hood latch and open hood.
Access Rubber Grommet
Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
Fastener Locations

Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
Remove Push In Fasteners
Remove the push pins attaching the fascia to the upper radiator closure panel.
Headlamp Jack screws

Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
Roll Fascia Forward

Roll fascia forward to clear way for headlamp housing removal.
Disconnect wire connector from back of lamp socket(s) and/or bulbs.
Remove Headlamp Housing

INSTALLATION
CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

Place headlamp housing into position.
Connect wire connector to lamp socket(s)
Verify headlamp and signal lamp operation.
Install jackscrews to attach headlamp housing to crossmember.
Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
Install nut on fascia stud through the splash shield access hole.
Verify headlamp operation and alignment


1helpful
3answers

2001 chrysler 300m - I need to find the fuse for the drivers side seat heat and for the charget inside the arm rest console. Might be the same fuse

If it is not in the fuse box under the dash, by the driver's legs, then it may be in the box by the battery under the hood. The fuse boxes should have legends on them, but if they don't and you don't want to start randomly removing fuses, you can buy a fuse (continuity) tester at the car parts store relatively inexspensively. This tool allows you to test fuses without removing them.

Hope this helps,
matt
1helpful
1answer

Changing the headlight on a chrysler 300m

Not as hard as this sounds, but not as easy as most vehicles either.

Pop open the access hole in the wheel well and remove the fascia screw that points down near the hole.

Remove the 3 plastic rivets on the top where the grill meets the cross beam

Remove the fascia retaining nut accessed through the hole in the wheel well.

Pull the fascia down and forward to open access to the headlights. It might be a little stubborn.

Remove the two long mounting screws holding in the headlamps. Careful not to strip them.

You'll have to wiggle and maneuver the headlights out. You'll have to bend the fascia away, but it's plastic and will give. It's not difficult, but it takes a little finesse.

Once the bulbs are replaced, reverse the process.
1helpful
1answer

How do you replace headlamp bulbs on 1999 chrysler 300

You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
Tell me if this works for you?
HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
REMOVAL
  1. Release hood latch and open hood.
  2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
  3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
  4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
  5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
  6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
  7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
  8. Remove headlamp housing Remove Headlamp Housing
INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
  1. Place headlamp housing into position.
  2. Connect wire connector to lamp socket(s) and/or bulbs.
  3. Verify headlamp and signal lamp operation.
  4. Install jackscrews to attach headlamp housing to crossmember.
  5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
  6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
  7. Install nut on fascia stud through the splash shield access hole.
  8. Verify headlamp operation and alignment
2helpful
1answer

Ying to change the battery.. Cant remove air filterhousing

To remove the battery in my 2001 300m you have to take off the front passenger side wheel/tire and remove the access panel and the battery will come out.
Not finding what you are looking for?

93 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...