Question about 2003 Mitsubishi Eclipse Spyder

1 Answer

No Radio No Clock.Help

I cut My Antenna wires now i have no Radio, No Clock, No Keyless Entry. I just want my antenna to stay down help me please.lol thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 88 Answers

When you cut the wires you most likely blew a fuse.

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many wire harness clips connect to rcdlr module on 2007 impala besides the antenna


2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry
Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html
May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...


Dec 01, 2015 | 2007 Chevrolet Impala

1 Answer

Antenna


The only reason to have an electrical wire going to the antenna is for a motor that raises and lowers the antenna. The antenna cable to the radio is the only wire on the antenna.
To replace the antenna, you have to remove it from where it connects onto the car, then lift it out from there. The antenna and the cable cannot be separated, it's all one piece. You pull the cable off of the back of radio, and tie a strong string onto it, because when you lift out the antenna, the cable will be pulled out from under the dash and to wherever the antenna is situated and out that hole. Now tie the string onto (hope you had a long string, lol) the end of the cable on your new antenna and cable, and stick the end of the cable into the antenna mounting hole. Pull the string from under the dash by the radio and you will bring the cable back into the dash and where you can plug it into the old radio and listen to good old music again !

Feb 13, 2013 | Suzuki Alto Cars & Trucks

1 Answer

Vp commodore antenna goes up when ignition is turned off


recheck the wiring and connections and check for a proper earth wire on the antenna unit

Jun 06, 2017 | Cars & Trucks

1 Answer

My 1990 Honda Accord radio antenna motor functions opposite to what it is suppose to be. When radio is on the antenna down, when the radio is off antenna up. Even with this reverse function I can feed the...


first of all, is your radio factory or aftermarket? If its factory the you probably have a bad ground or a short in the radio power to antenna. If its after market, then the remote antenna wire is hooked up wrong. Check to make sure the antenna wire is hooked up to the antenna. Good luck

Feb 21, 2011 | 1990 Honda Accord

1 Answer

My radio goes on but i get ecode message also my antenna does not go up


always check your fuses first , there are multiple power wires for the radio one for the radio, possible one for the clock, possible there may be one for the power on the motor used to raise the antenna take the radio out and test the power to the motor that raises the antenna up and down.

Dec 12, 2010 | 1999 Mitsubishi Diamante

1 Answer

How do i program keyless entry remotes on a 1995 Chevy Monte Carlo


open the trunk, pull the carpet back, were the radio antenna is you will see a single wire connector. take a jumper wire and hook to this connector and ground it to the radio antenna. you should here your door lock, it should lock and unlock at this time press any key on the remote and you should here the locks activate again . then unhook the connector from ground and try your remote it should be programed now.

Jan 10, 2010 | 1995 Chevrolet Monte Carlo

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

1 Answer

Hello. My antenna is connected to the back of my


The panel snaps on and off from the inside of the trunk up to the wheel well. There are 2 10mm bolts on the drive's side and 1 on the passenger side. You have to take the little cover off the driver side shock access to find the 2nd one. then pop the plastics off starting @ the trunk. There are 2 wires on the antenna unit; a single power wire on the motor, and the fat black antenna wire. If there is not a connector on the motor itself, you will need to get to the wires behind the radio and cut the "blank" wire WHILE THE RADIO is ON and the ANTENNA is in the UP POSITION! Failure to do this step will mean NO radio reception to speak of. DO NOT unplug ANY of the connectors on the back of the radio without first calling a dealer and getting the code to activate said stock radio. You will need this code if your battery goes dead as well.

Mar 26, 2009 | 1996 Acura Integra GS-R

2 Answers

Radio Stations are all static


If the antenna isnt there... that may be the problem!! LOL

Have you tried an aftermarket antenna directly to the radio to see if it works properly?

Fixed MAST antennas usually designate a standard 31" antennas protruding from the wheel well on either the passenger or Driver side.... not the bumper.

A solution to the fixed mast/car wash problem is to go with an interior glass mount or hidden antenna. This keeps your wiring out of the outside corrosive environment as well.

http://www.autotoys.com/pics/793new.jpg is one version
http://motorcyclestuffwarehouse.com/images/14721_kur_853_tt_h_pu.jpg is another type.
Finally...
http://akamaipix.crutchfield.com/products/2005/120/h12044UA200-f.jpeg





Jan 10, 2009 | 2003 GMC Envoy

Not finding what you are looking for?
2003 Mitsubishi Eclipse Spyder Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...