Question about Cars & Trucks

Open Question

Location 2004 dodge ram 1500 4x4 Central Axle Disconnect (CAD)

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: location of oxygen sensor

I believe you may have three (3) O2 sensor, (2) of the sensor is on ether side of the exhaust down pipe and some times called up stream O2 sensor, the third O2 sensor know to some as the down stream O2 and is after the Catalytic converter.
The up stream O2 monitors the left and right side banks and sends signals to the ECM to make the adjustments to the injectors to keep the proper air/fuel ratio. 
The down stream O2 monitors the catalytic converter and sends signal to the ECM if the catalytic converter has gone bad.
Good luck and hope this helps. If you get it scanned at Auto Zone, they should be able to let you know which O2 has gone bad so as to not change all three. You could always check the wire harness to the down stream O2 for corrosion. Keep me posted

Posted on May 29, 2009

  • 87 Answers

SOURCE: Replace the front u joint on the axle half shafts

You need to remove the front hub and bearing assembly's to remove the front axle shafts.

Posted on Jul 29, 2009

  • 1 Answer

SOURCE: what is the front axle on a 2004 dodge 2500hd 4x4

change u joint on front axle

Posted on Aug 30, 2009

  • 59 Answers

SOURCE: what size is the axle nut on the 2004 dodge ram

The size is between 1 1/8 in to 1 1/2 in.

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the vacuum shift motor located?


Gordon, I will take a guess, the Vacuum shift actuator/motor is located on the front axle. Check the attached pictures of actuator and how to replace video,links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagnosing 4WD Engagement Problems on Dodge Ram pickups
Front Drive Axle 4wd Vacuum Disconnect Motor 1AFWA00007
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram

May 18, 2016 | 1983 Dodge Ramcharger

3 Answers

1996 dodge ram 3500 5.9 diesel. wont engage 4 wheel drive. messed with vacuum line and it started working.so bought new lines replaced them . now it don't work at all.can the control switch be


If you are getting vacuum I would check the CAD (Center axle disconnect). You may want to go to a posi-Lok cable actuator if you're going to replace the vacuum actuator, better performance and you know it's going to engage!

Jan 07, 2015 | 1996 Dodge Ram 3500 Club Cab

1 Answer

I have a 2000 Dodge Ram 1500 truck with problems engaging the 4x4. I have checked the CAD. The vacuum does switch sides and the fork does move from side to side when FWD is selected. The truck acts


The fork must not be moving enough or the vacume is to weak. Also there is a vacume plunger in the vacume switch on the trasfere case make sure that is working. light oil can free it up or replace it

Oct 22, 2014 | 2000 Dodge Ram 1500 Truck

1 Answer

Where is the abs sensor located on 2004 dodge ram 3500 4x4


depending on your abs system, they are both front wheel hubs, and one on top of rear axle (this one fails most often and cost about $20 @autozone)

Aug 02, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

I have a loose vac line from the rear axle drivers side going to I have no idea where. Where should this line attach?2004 Dodge 3500 5.9.


I've seen some 4-wheel drive vehicle have vent tubes coming from the axle housing. Are you sure it's a vacuum tube?

Jul 11, 2012 | 2004 Dodge Ram 3500 Truck

2 Answers

What is the front axle on a 2004 dodge 2500hd 4x4


AAM is american axle manfactur its is equal to say a dana 60 that was use in dodge chev ford truck for years you could find out more buy goggleing it

Jul 31, 2009 | 2004 Dodge Ram 2500

1 Answer

Replace the front u joint on the axle half shafts


You need to remove the front hub and bearing assembly's to remove the front axle shafts.

Jul 29, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

Growling coming from front differential


There's not really a best way. If the axle half shafts bolt to the housing just drop it right out. If not you'll have to remove both half shafts from the wheel hub. Disconnect the drive shaft, and drop it out.

Mar 26, 2009 | 2004 Dodge Ram 1500

1 Answer

4x4 not working 1999 1500


need to check the central axle disconnect (cad) to make sure the vacuum lines are still attached, and check the vacuum pump to make sure it is working when you select 4wd. cad located on passenger side of front axle tube, vacuum pump located on transmission crossmember

Jan 08, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...