Question about 1999 Mercury Cougar

1 Answer

Don't know what they meen by push pins - 1999 Mercury Cougar

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 159 Answers

Need more info

Posted on Dec 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the plastic push pins from the inner fender?


The center of the push pins pull out for removal of the retainers I used a pair of side cutters to pull the center out be carful not to cut it off or you will have buy new ones

May 22, 2014 | 2006 Chevrolet Trailblazer

1 Answer

How do you replace fuel filter?


If it's a 4x4 the filter is under the driver side door on the frame, if it's a 4x2 then the filter is ahead of the passenger side wheel on the frame. Pull the fuel pump fuse from under the hood and crank it over to relieve some fuel pressure and ensure that the fuel doesn't shoot out all over the place. Then unscrew the band clamp off of the filter. If the fuel lines have the plastic pin type retainers just pull the pins out and pull out the filter. If it has the metal auto-locking spring couplers then you need a 5/16" fuel line disconnect tool. Wiggle the line/filter, push the tool into the coupler all the way and turn and pull the fittings apart. Put the new filter back in with the flat end facing the rear and push the pins back in/push the couplers back on and re-tighten the band clamp. Put the fuse back in the under-hood fuse panel. Turn the key from off to run about 5 times to cycle the fuel pump and prime the lines. Check to see if there is any gas leaking and if there isn't start it up.

I don't know the above answer that I found can do for you or not. Good luck!

_____________________
autocom cdp pro car diagnostic

Jun 08, 2012 | Pontiac Cars & Trucks

1 Answer

Can anyone tell me what Diagnostic OBD Code P2238 meens for a 2004 Toyota Camry?


Most of the codes for those readers are not in the book/manual. Only the common ones are. You can search online at the readers website or just enter the code number and usually you cna find the issue easily. I don't even know where my book is anymore. I just plug it in and then hop online. its so much faster.
You can buy a new one:

May 22, 2012 | Cars & Trucks

1 Answer

Replacing the back hatch (door). I need to get the handle free to change out the key barrel. There is a long nylon threaded screw holding one end of the handle from inside the door panel. Once I get this...


I don't remember having a long nylon screw in this. Open the hatch, remove the sheet metal screws that work with the push pins to secure the interior cover. After removing those screws carefully pry the push pins up till they come free from the hatch. This will give you access to the lock assembly. remove the "C" clamp that holds the lock in place after disconnecting any rods that maybe attached to it and the lock should come out toward the outside of the vehicle. There should be no reason to remove the molding.

May 15, 2011 | 1999 Plymouth Voyager

1 Answer

Changing a peugeot 306 ignition barrel i cant figure out how the release mechanism works any help


you need to push on the pin on the side of the barrel while slowly turning the key until pin pushes through.
but if the barrel is being replaced you will be able to drill through the locking pin

if this was any help let me know
cheers
mike

May 26, 2010 | 1998 Toyota Corolla

1 Answer

NO REVERSE, FORWARD GEARS IN REVERSE


i think you meen you only have reverse and no forwards gears?
if so its likley to be the linkage for forward gears look at the gear box to see if any thing is hanging off a cable or push rod it could also be up in the car under the gear leaver

Oct 30, 2009 | 1995 Jeep Grand Cherokee

1 Answer

I have a 1993 chevy truck I'm trying to replace actuator i've taken the steering wheel off and I don;t know how to get the next part off. I don't know how to get the round part with fins that the pin...


ok they make a steering wheel compression tool for the plat but you can get it off without the tool but its hard there is a snapring if you push down on the plate and remove snapring and the plate will come off

Aug 07, 2009 | 1993 GMC Sierra K1500

2 Answers

I don't know how to remove the pin type retainers or fasteners


with pencil push down on center of retainer and it will pop up

Mar 10, 2009 | 2002 Lincoln LS

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...