Question about Jeep Commander

Open Question

2007 jeep commander location input speed sensor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 154 Answers

SOURCE: location of speed sensor a for 99 dodge intrepid

The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Posted on Apr 02, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: turbine input speed sensor

NO the sensor is out side the transmission. And it might just be a bad connection due to being out in the eliments. On the 3.1 your going to have to jack up the car to get to it from underneath and you should see it on the passenger side may be on top, Sorry been awhile and carful not to brake the clips that hold the wire to the sensor when disconnecting.
Good luck and hope this helps

Posted on Apr 09, 2009

  • 316 Answers

SOURCE: input/turbine speed sensor circuit

Your speed sensor, is located on top of the transaxle, near the starter. To access it, remove the battery, then remove the battery tray (4 10mm bolts). You will see wires coming from the lower oxygen sensor, and they snap into the bracket that holds the speed sensor in place. The actual speed sensor has a 2 wire clip on it, and is held in place by the bracket and a 10mm bolt.

Posted on Apr 20, 2009

  • 151 Answers

SOURCE: Faulty speed sensor on a 2004 Jeep Rubicon

The speed sensor is located on the left side of the transfer case extension .

Posted on Apr 30, 2009

  • 1 Answer

SOURCE: transmission input speed sensor location

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 jeep commander it is showing a transmission speed input sensor code can I drive it to get me home or should it be fixed


it has to be fixed as it determines when the gears are selected against engine rpms
it is a sensor so it should drive but be prepared for selection problems while driving
check for wires and clean connections at the transmission

Jun 20, 2015 | 2008 Jeep Commander

1 Answer

Where is the speed sensor located at


their are two sensors one is the input sensor normally on the flywheel and a output sensor on the tailshaft of the transmission

Feb 24, 2013 | 2007 Jeep Grand Cherokee

1 Answer

P2767 input speed sensor circuit no signal


google either jeep commander or grand cherokee forums same vehicle basically post question there

Feb 04, 2013 | 2008 Jeep Commander 3.7

2 Answers

Jeep Commander 2006 with a diagnostic code of P2767. What is the repair for this?


That errror indicates that you have a defective Input Speed sensor.
NAPA has it by me for about $35 part # ATP 16494
Looks like 1 bolt to remove and replace

Aug 14, 2011 | Jeep Commander Cars & Trucks

1 Answer

Where is the speedometer cable located on a 07' jeep commander 4.7l v8 on the transmission? Please be specific as possible. Thank You


Your Jeep doe not have a speedometer cable. The speed is calculated by the PCM ( vehicle computer) by input values that are received from the vehicle speed sensor. This issue is most likely not repairable by the average person without the proper scan tool required to do so.

Jun 01, 2011 | 2006 Jeep Commander

1 Answer

Where is the speed sensor on a 93 jeep grand cherokee laredo?


Hi, the output speed sensor in located on the left side(drivers side)at the rear of the tranmission. The input speed sensor is located in the front of the transmiison on the left side as well, and yes both speed senors are interchangable.
Take care

Aug 04, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

2008 Jeep Commander with 5.8l Hemi problems with instrument panel


Have shop run an OHM test on your transmission sensors -- then have them replaced and rerun the OHM test. -- it's more than likely an input speed sensor that is not working properly and telling the jeep to go into "limp mode" hence your speed isn't changing but it can't read the actual speed.

Apr 13, 2010 | 2006 Jeep Commander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

532 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...