Question about 2007 Chevrolet Equinox LS

1 Answer

Wiper motor 2007 equinox

After removing the bolts, the windshield washer compartment will not pull out so I can replace the pump..how do I remove the compartment

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Chevrolet Expert
  • 180 Answers

Isn't the washer motor on the reservoir tank?

Posted on Dec 28, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 205 Answers

SOURCE: Rear windshield washer motor works, but no fluid comes out

Rear washer may have it's own reservoir . Can you hear a pump humming when you activate the washer? Look in the under flooor compartment

Posted on Mar 22, 2009

  • 3600 Answers

SOURCE: Rear windshield wiper broken 2007 Chevy Tahoe.

Once you get the nut off of the shaft use a pair of plyers or channel locks and wiggle the base back and forth it iwll come off and then you can replace the wiper assembly without taking anything else off.

Posted on Aug 26, 2009

  • 265 Answers

SOURCE: How can I tell if the windshield wiper motor is

wiper pump - or the hose is clogged/pinched

Posted on Mar 03, 2010

ftw1952
  • 10319 Answers

SOURCE: How do you remove the windshield wiper arms

The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

Posted on Apr 07, 2010

  • 7353 Answers

SOURCE: Is there an actual fuse for the washer pump, not

Fuse #45, under hood fuel panel.

Posted on Dec 21, 2010

Testimonial: "Thank you. I checked on that myself and this fuse is labeled as the Front, Rear Washer."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I purchase fuse #45 for my chevrolet equinox lt 2007 in richmond, va


It sounds as if the windshield washer pump, located at the base of the windshield washer fluid reservoir, has lost it's seal. When this occurs, washer fluid seeps into the pump and shorts it out. I advise that you remove the pump to confirm this before replacing the fuse. A replacement wind washer pump and fuse can be found at your dealer, local auto parts store or the internet (Rockauto.com has always been a great source for quality parts at a very competitive price and I use them all the time). Hope this helps.

Mar 15, 2014 | 2007 Chevrolet Chevrolet Equinox LT

1 Answer

Wiper motor removal and replacement


Remove wiper arms, remove lower windshield plastic cover, remove wiper washer connector, remove 8 8mm wiper housing, disconnect wiper motor remove from car...remove 3 10mm bolts and center 8 mm bolt and remove motor. ..reverse and reinstall

Feb 26, 2014 | 2003 Mercury Grand Marquis

2 Answers

Windshield washer motor


there is a retainer ring that holds the pump inside the container.. it comes off and the pump conmes out of the bottom..

Dec 28, 2013 | 2007 Chevrolet Equinox LS

1 Answer

Where is the wiper motor for 2006 pontiac g6, removal and installation?


The wiper motor and transmission is located in the engine compartment at the top. Remove the black box that slightly covers the windshield bottom. You will be able to remove the wiper motor and transmission (they're connected) with 3 bolts. You must first remove the windshield wipers from the transmission. Do that by taking the circular black caps off of the base where there connected and remove the bolts. Apply pressure where the wiper (not the blade) curves upwards, and pull up on the connected area. They are spring loaded and will come right off.

Dec 20, 2010 | 2006 Pontiac G6

2 Answers

How do I fix my window washer pump on my 2000 dodge caravan?


One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif

Aug 27, 2010 | 2000 Dodge Caravan

1 Answer

Where is the windshield wiper motor on a 2007 Dodge Caravan and how do I replace it?


Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

f7c141f.jpg

Sep 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

1 Answer

Windshield washer doesn't work. I'm looking for the location of motor


Service and Repair
  1. Turn ignition switch to the ACCY position, then set wiper switch to the "PULSE position.
  2. Turn ignition switch off when wiper arms are at bottom and not moving.
  3. Lift wiper blade assembly up from windshield.
  4. Pull out retaining latch with a screwdriver.
  5. Pull wiper arm assembly off transmission driveshaft.
  6. Disconnect battery ground cable.
  7. Disconnect hose from washer hose.
  8. Remove five air inlet panel retainers.
  9. Push washer hose into firewall.
  10. Remove air inlet panel from vehicle.
  11. Using wiper transmission separator tool No. J-39232, or equivalent, remove transmission drive link socket from wiper motor crank arm.
  12. Pull two harness connector retainers out of wiper motor connector.
  13. Disconnect two harness connectors from wiper motor.
  14. Remove wiper motor attaching bolts and stud, then the wiper motor from the vehicle.
  15. Reverse procedure to install.

Dec 10, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
2007 Chevrolet Equinox LS Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...