Question about 1989 Chevrolet Corvette

1 Answer

Wiper adjustment when the wiper rotates it is not aligned with the windshield

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Chevrolet Expert
  • 180 Answers

Slight adjustments are under the cowl on the wiper transmission linkage, are you sure it didn't get bend as a result of ice on the windshield or something

Posted on Dec 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust the wiper position?


Loosen the mounting nut..use a flat screwdriver or prybar to lift off the wiper arm off...set the arm where you need it remembering to align the little slots that are factory cut in the unit...tap down lightly into place and reinstall the lockdown nut.

Nov 24, 2016 | Cars & Trucks

3 Answers

Adjust pressure for Citroen picasso 2002 winscreen wipers


Are you talking about your windshield wipers? Try replacing them.

Feb 19, 2015 | 2001 Citroen Xsara Picasso

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

How do I replace wiper blades


First, pull on the wiper arm until it raises and locks into the service position. The wiper arm will stand by itself once you raise it past a certain point.
Then find the clip on the underside of the wiper arm (rotate the blade slightly to get to it.
Press the clip in while simultaneously pulling the old wiper blade off the wiper arm. You can then discard the old blade.
Align the new wiper blade with the wiper arm track. Slide it along the track until you hear it click.
Repeat this process with the other wiper blade to complete the replacement of wiper blades on your Highlander.
Return the wiper arms to their normal position against the windshield. Done!

Dec 05, 2010 | 2005 Toyota Highlander

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Oct 01, 2009 | Ford Taurus Cars & Trucks

1 Answer

Removing windshield wiper assembly ford excursion


Wiper Pivot Arm Removal and Installation
  1. Lift the windshield wiper pivot arm to the full upright position.
  1. Remove the windshield wiper pivot arm.
    1. Release the locking tab.
    1. Remove the windshield wiper pivot arm.
52fed05.gif
  1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
    To install, reverse the removal procedure.

Jul 02, 2009 | 2005 Ford Excursion

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

2 Answers

Instructions aligning wipers on a 1998 Gran Prix GT


Loosen the nut on top then realign them then tighten the nut. I have to do mine every time they get frozen.

Apr 04, 2009 | 1998 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...