Question about Cars & Trucks

1 Answer

Audi a6 wiper motor

Front wiper not working, have changed fuse, was making a grinding noise before it stopped

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 159 Answers

Verify that their is no obstruction if not replace motor but before if you know somebody with a good scanner have him try to activate the motor if it run it may be the linkage

Posted on Dec 28, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: noises when turning steering wheel

check cv joint

Posted on Jul 16, 2008

  • 2 Answers

SOURCE: wind shield wipers just stopped working

ahhhh ya there is

GOOD LUCK ON THE RELAY, THERE ISN'T ONE, IT IS PART OF THE GEM MODULE, AKA LIGHTING CONTROL MODULE.



Hummmm, so you replaced the wiper motor with a new one, and also the "multi function" switch….the black or chrome lever that operates the wipers and the turn signals…correct? That lever/switch is the most common failure for this problem that I have seen.
If you have replaced both of those, have your mechanic check to see if you have an "intermittent wiper governor". This part is about half the size of a cigarette box and just plugs into the wire harness for the wipers. Look under the left knee area of the driver side dashboard and follow the wire harness from the steering column going to the wiper motor. There should be this box plugged into the wire harness within that section of wires.
Some models had this governor, some do not….so you will have to check to see if yours is equipped with it or not. Your mechanic should be able to tell you this. We have replaced a few of these governors over the years, usually for the intermittent part of the wiper not working…but it COULD be the problem in this case

Posted on Jan 13, 2009

Technopro
  • 243 Answers

SOURCE: fuse box in a audi a6 1995

Fuses are located by the side of the dash board when you open the driver's door. The fuel pump fuse is situated in there.

Posted on Feb 08, 2009

auditech13
  • 43 Answers

SOURCE: how to remove audi a6 wiper blades

The problem with this wiper blade set up is the slides get jammed up w/ crude.  You should lubricate the slides and they should slide off.  Then carfully lift the arm and remove the blade.  Warning you should never leave the arm in the upright position.  Windshields get cracked this way.  Also note the pivit points the blades attach too.  These will normally sieze up and cause clearing issues even with new blades.  Lubricate these pivit points and use a pair of channel locks to move it back and forth until it will go 360 degrees with your fingers.  Install is in reverse order of removal. 

Posted on May 28, 2009

TDISLine
  • 1874 Answers

SOURCE: rear wiper has stopped working in audi a3 - where

Yes, is the same fuse nr.41 (15A) !
For Audi A3 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
The fuse nr.41, (the second fuse from right to left direction, on the second row from bottom to upper direction, on the fuse box), F41 (15A) = Rear screen wash & wipe system !!!
Replace blowed fuse with new one and problem will be solved quickly !
Please rate my response. Thanks!

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi a5 problems


I think the grinding noise you are hearing is the ABS pump coming in. Check the wheel speed sensor rings to check is they are the same. If they are different (number of slots} the ABS control module will be confused and starts the pump. I had that problem with my A6.

Dec 19, 2013 | Cars & Trucks

1 Answer

A6 wipers


How do you know motor is fine, you jumped a wire across from battery to motor? if what you say is correct then it has to be the wiper control switch, if when u jump wire across and motor turns but not wipers the the attachment from motor to wiper assembly is stripped, disassemble and find if it's shaft or plate that's stripped happens when people don't clean windows off from snow ice and just turn wipers on.

Jun 09, 2012 | 2005 Audi A6 2.0

1 Answer

Front wipers have stopped working on audi a3, how do i change the fuse?


Replace Fuse no.# 31 - F31 (25A - white color) = Wiper motor. See picture below:

10_12_2011_11_35_38_am.jpg

Oct 04, 2011 | 2005 Audi A3

1 Answer

Need to fit new windscreen wiper assembly, cant get new one to go back in


How to change a wiper assembly & repair wiper mechanism on 2001 Audi A6

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Please do rate my response. Thanks!

Feb 15, 2011 | 2001 Audi A6

1 Answer

Hi, How do I remove rear window vinyl on a Audi A6 Avant -99. Reason is I want to check why the rear wiper doesn't work anymore. I have checked the fuse at main fuse panel left side of instrument panel....


if it was me i would stop by your local Audi dealership in the parts department and they be able to print you off the pictures and diagram you will need wish you the best of luck Michigan Man.

Oct 03, 2010 | 2000 Audi A6

1 Answer

Where is the washer bottle for the rear wiper in a 2007 audi a6 avant?


think it runs off of the front bottle and its the same washer motor ,it has a two stage action

Dec 22, 2009 | 2007 Audi A6 Avant Wagon

1 Answer

Front wipers stopped working


Try to run a ground test on the motor, If it gets power, then you neeed to replace the switch.. if it doesnt run with the ground test, then you need a wiper motor.

May 20, 2009 | 2005 Audi A4

2 Answers

LOUD Grinding Noise When I Shift to Park


you are going to have to get taht transmision checked on. all you have to do for the lights is find the fuse panel and find the schematic for the fuses and change them out.

Jul 13, 2008 | 1996 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...