Question about Toyota Avanza

1 Answer

Avanza 3szdaa timming marks

1.5 avanza 2007 need timming marks?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers

Alldata.com

Posted on Dec 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need Toyota Avanza 1.5 TX timing chain marks. Please send diagram or picture with measurements if possible. Vehicle Identification Number (VIN) isL MHFM1CA3N8K004063. I'm in South Africa (RSA)


find an auto spares shop and get a workshop manual for the car or any toyota car that has the same engine as yours
all the procedure details are in the manual

Nov 30, 2016 | Toyota Cars & Trucks

1 Answer

How to set the valve timing on dg engine Toyota avanza with no marks on the chain


The marks will be on the cogs and the plate T.D.C mark on the front pulleyand cover.

Jan 22, 2016 | Toyota Cars & Trucks

2 Answers

Need picture of timming marks


has the timing chain been replaced

Mar 27, 2014 | 1984 Datsun 2.8

1 Answer

Toyota avanza 1.3 fuse box


Mobi saya toyota avanza 2004, sewaktu saya melepaskan accu dan memsang kembali, ternyata sistem remot tidak hidup/tidak berfungsi. mohon solusinya. terimakasih.

Sep 15, 2012 | 2007 Toyota Avanza 1.3

1 Answer

2002 Hyundai Acent 1.5 sohc,need info on cam timming


didnt you mark it before you removed the old belt??

Nov 01, 2009 | 2002 Hyundai Accent

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

Timing marks


you should have timming marks on the front engine block. if you see it you will need a timming light to set it very cheap to buy. if you do not see any timming marks and you have a distributer losen it a little but with the car running. now with the car running turn the distruber left or right until you hear and feel the car idle high. once you feel it idle low go back up until it idle high and keep it there and tighten the distruber back. turn the car off and try starting it back up. it should start right on time with the correct timming and idle. good luck

Jul 08, 2009 | 1995 Chevrolet Monte Carlo

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...