Question about 2008 Honda Civic

1 Answer

Remove cowling Reverse camera

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Double posted, the cowl is in front not rear.
back up one post,

Posted on Dec 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a wiper motor fro replacement


you have to remove the whole cowl with the motor in it (1) take off the wiper arms (2) take off the windshield cowls under the wiper arms by removing the screws and washer hoses (3) remove the vacuum control valve from the wiper motor cowl (4) remove the clips and bolts that hold the cowl to the firewall and remove as an assembly (5) remove the motor and replace it with the new unit (6) reverse removal procedure

May 21, 2015 | 1999 Lincoln Town Car

1 Answer

How to replace a front windshield wiper motor?


You need to pop your hood up, remove your windshield wiper arms but make sure you mark the position of the arms marking on the arm and arm attachment for re-installation alignment, Remove rubber seal and plastic screws (Phillips head), remove windshield wiper water line from left side, then carefully remove plastic cowl. Under neath will be your wiper arms and motor. You can remove all 8 mm bolts and then remove whole plastic cowl and deatach the wiper motor. Installation is in reverse order of removal.

Oct 14, 2013 | 2002 Ford Windstar Cargo

1 Answer

Where is the ecm located


back of the engine compartment on passenger side:

Removal & Installation

3.0L (VIN S) Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  8. Remove the retaining bolts and the PCM.
  9. To install, reverse the removal procedure.

3.0L (VIN U, 2) Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the evaporative emission (EVAP) canister purge valve return tube at the intake manifold and position aside.
  8. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  9. Remove the retaining bolts and the PCM.
  10. To install, reverse the removal procedure.

May 13, 2011 | 2002 Ford Taurus

1 Answer

Where is the cabin air filter in 2001 jeep cherokee


It is under the passenger side cowl grill. Remove the passenger side windshield wiper, remove the cowl, remove filter and housing. Install new filter and housing in reverse order.

Mar 20, 2011 | 2001 Jeep Grand Cherokee

1 Answer

Where is the. 2001 Ford Taurus Engine Computer ECM locate


It's in the engine compartment, back passenger side, under cowl. here are instructions from autozone.com:


Removal & Installation
3.0L (VIN S) Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  8. Remove the retaining bolts and the PCM.
  9. To install, reverse the removal procedure.

3.0L (VIN U, 2) Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the three RH cowl panel clips and remove the RH cowl panel.
  5. Remove the clip on the water shield.
  6. Remove the three RH water shield screws and remove the RH water shield.
  7. Disconnect the evaporative emission (EVAP) canister purge valve return tube at the intake manifold and position aside.
  8. Disconnect the powertrain control module (PCM) electrical connector and remove the gasket.
  9. Remove the retaining bolts and the PCM.
  10. To install, reverse the removal procedure.

Oct 15, 2010 | 2001 Ford Taurus

1 Answer

Location of ecu on a 2005 ford freestyle


Keep in mind the definitions:
* ECM = Electronic Control Module (prior 1995 computer, OBD1)
* PCM = Powertrain Control Module (1995 and newer, OBD2)


Ford Freestyle 2005 - Powertrain Control Module The PCM is located in the ine compartment, passenger side, mounted to the cowl. Removal & Installation procedure:
  1. Retrieve the module configuration.
  2. Remove the cowl panel grille.
  3. Disconnect the 3 PCM electrical connectors.
  4. Remove the bolt and the PCM.
To install:
  1. Installation is the reverse of removal.

4f23c78.gif

Hope helps (rememnber rated this).

Jul 14, 2010 | 2005 Ford Freestyle

2 Answers

Location of wiper motor 1999 chevy silverado


under hood drivers side on fire wall between engine and brake master cylinder take off wiper arms slide tab at bottom lift off -- un- screw cowl the cowl is in 3 parts -unscrew center with hood closed first the screws are recessed about an 1-1/2 below the top of cowl open hood and unscrew the both sides of cowl and remove than remove center watch the washer hoses now will have access to the wiper transmission mark where transmission is before unbolting motor and transmission remove motor install is in reverse

Feb 10, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How do i install a new wiper motor on my truck?


you have to remove the cowl (panel under wiper arms) by removing the wiper arms and taking off the screws in cowl. The wiper arms need to be pulled away from windshield then you slide the clip at the base over and pry the wipers off. Under the cowl is a screen you remove. Then you can get to the wiper linkage. You can pop off the linkage with a prybar or a big screwdriver. Once it's off you take the bolts holding the motor out unplug the connector and reverse order for installation. The linkages can take some serious manhandling to get back on!

Feb 07, 2010 | 1993 Dodge Dakota

2 Answers

Where is the cabin filter located


The cabin air filter is located directly underneath the cowling at the base of the windshield on the passenger side of the car.
To access the cabin air filter, you will need to remove the cowling. First, open and lift the hood. Second, locate two plastic pins securing the plastic cowling at the base of the front windshield, on the passenger side. One is located under the wiper blade, near its base. Use a small screwdriver or similar tool to carefully lift/pop up two plastic pins securing the cowling, taking care not to damage the plastic pins. (You want to lift the pins, and not the anchors that look like washers beneath the heads of the pins. Carefully pull the plastic pins and their plastic anchors (once you pull the pin up, you can safely remove the anchor). Take caution not to damage the pins and anchors as you will need them to rescure the cowling when you are finished replacing the cabin air filter.
Before you remove the cowling, carefully pull back the rubber gasket and windshield washer fluid tubing at the base of the cowling. You can now safely remove the cowling, and you will see the cabin air filter below.
Remove the old cabin air filter and replace it with a new filter.
Reverse this process to reinstall the cowling, gasket, and pins once you have replaced the filter.

Oct 16, 2009 | 2005 Pontiac Grand Prix

1 Answer

Bad wiper motor on 1996 dodge grand caravan


According to the Haynes repair manual Chapter 12:

1. Disconnect the negative battery cable
2. Detach washer hoses, lift the wiper arm covers and mark the wiper arm locations on the pivot shaft for later re-installation. Remove the wiper pivot nut and remove the wiper arms.
3. Remove the cowl cover (from chapter 11)
3a. Remove the wiper arms then remove the screws that hold the lower area of the cowl cover to the wiper module.
3b. Disengage the quarter turn fasteners that hold the outer ends of the cowl cover to the wiper module.
3c. Open the hood and release the wing nuts that hold the front of the cowl cover to the wiper module.
3d. Close the hood but do not latch it. Now remove the outboard screws and lift the cover up enough to get to the washer hose.
3e. Disconnect the washer hose from the right washer nozzle. Close the hood but do not latch it. Lift the cowl cover toward the windshield and off the vehicle.
3f. Installation is the reverse of removal
4.Open the hood. Disconnect the wiper motor electrical connector.
5. Disconnect the windshield washer hose from the coupling inside the unit. Disconnect the drain tubes from the bottom of the wiper unit.
6. Remove the wiper unit mounting bolts. (Picture appears to be three (possibly allen head) bolts)
7. Remove wiper unit.
8. Installation is the reverse of removal. Wiper blade and wiper arm adjustment is measured with the wipers parked; correct adjustment is the lower wiper arm approximately 1.5 inches distance from the cowl cover and the upper arm approximately 2.5 inches from the lower arm. Operate the wiper motor and check that the wiper motor parks when the wiper switch is OFF.

Mar 21, 2009 | 1996 Dodge Grand Caravan

Not finding what you are looking for?
2008 Honda Civic Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...