Question about 2008 Honda Civic

1 Answer

Wiring/reverse camera Remove interior flashing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

The covers inside we called cards.
they are hardboard with vinyl covering. door cards, or wall cars. etc.
so on most cars, you start low and pull to allow the spring clips to pop
and release.
if not clear, the FSM covers all this, step by step.

Posted on Dec 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locating wiring for reverse


the easy way is to tap into the reverse rear white tail light wiring RUDY PEREZ.

Oct 10, 2014 | Cars & Trucks

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Driver side window on dodge caravan stopped working in the down position, is there a way to manually get it up?


Try wiggling harness that goes from post to door by hinges, or open wire loom up and see if any damaged wires. If worst comes to worst, I'd remove interior panel and try jumper wires directly to motor connector at least to get window back up. You can use a 12 volt or 14 volt cordless battery. Reverse polarity, reverses direction of the motor. FYI.

Apr 13, 2013 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

Need to find the reverse wire to hook up a peak backup camera thanks ernest


Hi!
You did not specify the yr and model of your vehicle, but the procedure is the same, remove the tail light assembly as specified on your owners manual to replace a light bulb. Apply the Parking Brake and turn the ignition switch to the RUN position (do not start the vehicle), press the brake pedal and place the Shifter in REVERSE. Remove the Reverse light bulb and use a test light grounded to the vehicle chassis to find which one of the two wires going into the reverse light socket is the 12v+, once located, replace REVERSE light bulb, place shifter lever in PARK and turn key OFF.
Splice the 12v+ wire and connect the 12v+ lead from your camera to it, get your Ground (-) from the vehicle chassis.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Dec 02, 2010 | Saturn SL2 Cars & Trucks

1 Answer

2005 chevy suburban- my back-up lights and interior dome lights do not work. All fuses appear intact? Suggestions?


you bcm (body control module is bad) to have the dealer replace it will run you about $400. a quick fix for the reverse light is to splice 2 wires into the wire for the center plug in your trailer wiring. now run a wire up to each reverse light, cut the green wire to each reverse light and **** conect them up. this is a seperate revers feed than the one from the bcm. the dome lights remove the light cover on the second set of interior lights (the one between the drivers seats). the two side bulbs are map lights the center bulb is for the dome lights. run a jumper wire from the right or leftside socket to the center socket. you dome lights will now turn on with just the use of that switch i replaced the back bulbs with led's soo there is no extra amp's being drawn. you could bypass the bcm but i could not find any wiring diagrams for it and i dont know if it can take the added amp's

May 31, 2010 | 2005 Chevrolet Suburban

1 Answer

Interior trim panel removal instruction


Normal 0 . Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.


If you don't have power windows you will have to remove the manual window crank. It is held in place by a clip on the back side of the base. To remove the clip, you will need a small hook (kind of like a knitting needle). Put the hook in behind the base, and grab the clip and pull it off. To replace it, slide the clip back on the window crank, and snap it back on the door.

May 31, 2009 | 2003 Volkswagen Passat

1 Answer

Power window motor replacement. window in down position


Normal 0 Disconnect your negative battery cable. Locateand remove the screws that hold your interior door handles in place (they maybe hidden by snap in, or snap on clips). Remove the interior door handles, thendisconnect the wire clips to the switches. Your panel is held in place by snapin clips; use a small pry bar to pull them from the door (try to get as closeto, or directly under the clips to prevent them from tearing out of the doorpanel). Once the clips are pulled, pull the panel upward to remove it from thedoor. Once you gain access to the interior of the door, you can remove your window regulator and re-position it, or replace it so it works.
Install in reverse.

May 26, 2009 | 1995 Ford Explorer

1 Answer

Remove door panel


Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

May 25, 2009 | 2004 Toyota RAV4

2 Answers

How to remove interior door panel on a 1997 caravan with ower windowq


Start by removing the negative battery cable from the battery. Then locate and remove the screws that hold the interior door handles in place (they may be hidden by snap in, or snap on covers). Once you have removed the interior door handles, disconnect the wire clips that go to your window and door lock controls.
I personally use a small pry bar to remove the interior door panel; it is held in by plastic snap clips. Try to get as close to, or directly under the snap clips as possible with your pry bar to prevent them from tearing out of the door panel. Once you have released the snap clips, pull the panel upward to remove it. Install in reverse.

I hope this information helps you, and I wish you luck on your repair.

Apr 24, 2009 | 1997 Dodge Caravan

1 Answer

Replacing an interior door handle


first remove the door panel after you have completed that remove the 3 bolts holding the handle in place, pull the handle out on the reverse side there will be a connecting rod with a retainer clip holding the rod to the door handle remove the retainer clip and rod and remove the broken handle follow instructions in reverse to reinstall new handle

Jul 19, 2008 | 1988 Ford Taurus

Not finding what you are looking for?
2008 Honda Civic Logo

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...