Question about Cars & Trucks

1 Answer

2002 Ford 7.3 no start

Engine turns but doesn't start

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 51,202 Answers

Run fault codes and look for cam/crank position sensor . check correct operation of the immobiliser. Do you hear the fuel pump when you turn the ignition on.

Posted on Dec 28, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ford Ranger doesn't idle when engine is warm. Why?

is the check engine light on is so have code read 1st-second try cleaning the throttle body where air goes into the engine where the rubber hose attaches clean with a throttle cleaner wipe cleaner out i say this due to the idle air control motor may be dirty,and last you may have a faulty egr valve

Feb 18, 2013 | 2002 Ford Ranger

2 Answers

2002 Ford Thunderbird turns over but won't start

Check for fuel at engine and for spark at coil

Nov 26, 2012 | 2002 Ford Thunderbird

1 Answer

My 2002 Ford Expedition has a stuck a.c., it doesn't heat up. I replaced the Temperature control unit and the motor for my heater actuator, still no heat? Please help?

Its a faulty heater control valve that is located in between the engine and the heater core or just before the firewall.

Jan 31, 2012 | 2002 Ford Expedition

1 Answer

What is the size of a serpentine belt on a 2002 ford taurus without the A/C Compressor

If its the 24 valve engine its13/16 x 82 1/8 and if its a 12 valve engine then its 13/16 x 85 7/8

Jan 19, 2012 | 2002 Ford Taurus

1 Answer


If this is a after market weekend mechanic boy racer alarm thingy then get a pair of side cutters and remove it .these things are made using inferior made in china micro chips and are ALWAYS going wrong

Dec 28, 2011 | 2002 Ford Thunderbird

1 Answer

2002 Dodge Caravan,3.3L,Engine won't turn over at the key.Battery,starter and relay are good.Relay doesn't function when plugged in.It has 2 feeds.If you run a ground to the ground side of the...

It has 2 feeds.If you run a ground to the ground side of the relay,engine turns over but doesn,t run ????? The PCM - engine computer isn't supplying the ground for some reason . Anti-theft system problem . Disables fuel an starting systems . Have you checked for codes ?DTC'S - diagnostic trouble codes .

Mar 04, 2018 | 2001 Dodge Grand Caravan

1 Answer

Truck runs then cuts off. it has fuel pressure ignition is good, has good compression. recently it has gotten to the point where it wont start at all. i put a gas soaked rag over the intake breather tube...

does the check engine light come on whenyou turn the key on for the bulb check? if it doesn't come on you may have a sensor shorted out and it kills the 5 volt reference signal that the ECM uses to power up the system an dlet the truck start.

Jul 22, 2011 | 2002 Ford Super Duty F 450

1 Answer

My 2002 stang has started jerking and sputtering. then my service engine soon light came on. any ideas what could be wrong?

There is to much to list that will cause this problem. from vacuum leaks to fuel pump to sensors. You need to have the codes read and repost. This will give you an idea where to start. just a note.... If you get an 02 code, it doesn't mean the 02 senosr is bad. same with all the codes. There could be other things that will pop a code.

Jun 27, 2011 | 2002 Ford Mustang

1 Answer

2002 ford taurus overheats. Just replaced radiator, waterpump, thermostat and heater core. what else can i do to repair. also, ford flushed the system.

About the only thing that you didn't list is the cooling fan. Are you sure that it's working properly? Drive the car until the engine starts to get hot. After awhile you should hear the cooling fan come on. After you have driven the car for a while, park it and open up the hood. If the upper radiator hose is almost too hot to touch, then check to see if the coolant fan is running. If it isn't, then turn the AC switch to "AC MAX". If the fan still doesn't come on, then a malfunction is indicated. Try to locate the fan control relay and swap it with another relay that has the same part number. Use a relay that will allow the engine to run. Allow the engine to reach operating temperature and see if the fan comes on after switching the AC switch to "AC MAX". If the fan now operates, then replace the relay. I hope this is helpful to you. Thank you for trying If this does not solve your problem, then post a comment and I will respond by getting into more advanced diagnostics.

Jun 25, 2011 | 2002 Ford Taurus

1 Answer

Fan will not turn off after engine is off on 2002 ford taurus what can be the problem

How long does the fan run after you turn the engine off? It is normal for the fan to run until the engine temperature is reduced. But if it doesn't turn off at all, then I would check the fan thermostat, it is probably bad.

Jun 01, 2011 | 2002 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15273 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides