Question about Cars & Trucks

Open Question

Airbag module location on 07 bf xr6 ute

Location of air bag module on 07 bf xr6 ute

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 71 Answers

SOURCE: air bag replacement in 2003 grand am

That is the only sensor to trigger the bags. The new module needs to be programmed to the car by the dealer or someone with a scan tool capable of that.

Posted on Nov 22, 2008

  • 56 Answers

SOURCE: malibu air bag module location

The module is under the passenger side seat,under the carpet.You will have to remove the seat to access it easier.Lift up the carpet and it will be mounted to the floor.

Posted on Mar 03, 2009

kallumin
  • 1 Answer

SOURCE: 97 ford taurus air bag module location

It"s in the steering column...

Posted on Apr 01, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: airbag light stays on

This is common on the beetle. More than likely it's diagnostic trouble code 00591 E24.
It will need to be reset with vagcom or vcds software. A few known trouble areas on the beetle that trigger this light are the seat belt buckles and the wire connectors under the seat. I've seen the connectors get loose and not make contact, and in one case the wires severed from sliding the seat. You might check this before you clear and reset.
Good luck...i hope this helps.

Posted on May 12, 2009

  • 14036 Answers

SOURCE: Trying to find location of air bag crash sensors

THE AIR BAG CONTROL MODULE IS ON THE FLOOR AHEAD OF THE CONSOLE.BECAREFUL YOU CAN CAUSE AIR BAGS EMPLOYMENT ACCIDENTALLY.THEY ARE DANGEROUS.THE DEALERSHIP HAS TO RETRIEVE AIR BAG FAULT CODE.

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of airbag module 2005 Chevy Classic 2.2L 4dr Sedan


Location of airbag module Mike, Air bag module is under right front seat.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
GM Saturn Airbag Air Bag Black Box EDR Event Data Recorder SDM Deployment...

Mar 24, 2016 | Cars & Trucks

1 Answer

I have a 2006 BF ute when i start it up it only runs for about 3 seconds sometimes i have to restart it 3 to 4 times before it will keep running when it runs for the 3 seconds it is like an old car when...


have the fault codes read and get some idea of what sensor/ servo has failed before you waste any more cash IT sounds like a MAF/MAP sensor or ambient air temp sender

Sep 11, 2013 | Cars & Trucks

1 Answer

2001 pontiac grand am air bag module reset


Yes!!! You can replace it yourself.(Dont let others fool you into paying extra or telling you otherwise.)
-This is for pontiac grand ams 1999-2005 only.
-There are no frontal airbag impact sensors nor are there belt tensioners.
-The SRS system consists of only the (driver airbag) ,(passanger airbag),and the (airbag control module) in 1999-2005 grand ams.

If you crash/wrecked and airbags deployed you will need.
-Driver and Passanger airbags
-Airbag control module

You can buy cheap airbags from a local junkyard any year from 1999-2005 will fit.
You can also find an airbag control module for cheap at your local junk yard BUT YOU MUST FIND ONE WITH THE SAME (PART NO.) AND (SERV NO.) AS THE ONE YOUR REPLACING.The (part no.) and (serv no.) should be at top left of airbag control module.However it does (Not) have to match numbers under barcode or the numbers at the far bottom right of airbag control module.

After you get both airbags and airbag module
-Disconnect car Battery
-Replace airbags
-Replace airbag module (under passanger seat)
-Double check all connections and connect battery.

Congradulations!Your airbags should be back online.

Notes: Two torx 35 head screws hold the driver airbag, access is through two holes behind steering column.
To remove passanger airbag you have to remove glovebox it uses (7mm)screws.After you remove you will see a pair of (10mm)screws holding airbag.
To remove airbag control module First remove passanger seat 2(15mm).Then after removing you will notice a raises area kinda like a vertical bump.Take a razor blade to your carpet and cut it to explose the module underneath.
The airbag module is held by three screws depending on the year of your car it varies.Most likely 3 (10mm).

Mar 24, 2013 | Pontiac Grand Am Cars & Trucks

1 Answer

Where is the airbag module located on my 02 Mercury Cougar? Thanks...


raineman_15_6.gif This picture is forYour air bag diagnostic monitor and also your driver air bag module &sliding contact. Your side air bag modules are at respective side of each front seat

Dec 02, 2010 | 2001 Mercury Cougar

1 Answer

Air bag flashing a fault code 32. Where is the Air bag modual located and can the code be cleared or is their more involved?


The air bag module is located behind the front bumper. IT IS NOT RECOMMENDED THAT ANYONE NOT QUALIFIED TO SERVICE AIRBAG SYSTEM ATTEMPT TO PERFORM ANY SERVICE. The airbag system will need to be checked by a qualified technician in that field. The airbag can inflate causing damage or personal injury. Please do not attempt any repairs yourself.

Jun 16, 2010 | Cars & Trucks

2 Answers

Where is the airbag module located on 2004 vw jetta


The airbag module is a serious safety device and should not be tampered with. The entire air bag system ie module , air bags, seat belt tensioners etc are treated as one unit and there fore not a serviceable item or part replacement there of. The module should be located in the bowels of the dashboard (yellow wiring ) and mounter to the bulkhead. Do NOT tamper or adjust any componants.Good luck

Apr 11, 2010 | 2000 Volkswagen Beetle

1 Answer

Airbag module location for 2004 Mazda6


it is positioned in the very centre of the dash board, behind the radio/Air con unit, it is bolted to the floor, you will need to remove the dash board and possibly the air con unit to access. once the module and air bags have been replaced it shouldnt need anything else.

May 21, 2009 | 2004 Mazda 6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...