Question about Mitsubishi Pajero

Open Question

Wiring code for Pajero reversing lights

Wire up reversing camera

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: reverse light wire code or color?

PLEASE UNDERSTAND that if you mess with any of the lighting on this vehicle it could cause the control module for the lighting system to malfunction and go out and this part the last time I replaced one was$970.00.

Posted on Sep 12, 2009

  • 68 Answers

SOURCE: Wiring 4 way flat trailer plug. brown wire running

you got brown for running parking light
green for right turn/stop
yellow for left turn/stop
white for ground
reverse lights are only wired on a 6 or 7 plug connector
make sure you on the dark green for right turn stop not the light green
the light green is for reverse

Posted on Jul 13, 2010

SOURCE: find reverse light wire in dash

it would be easier to run it from the back up wire in the rear you can see it better

Posted on Aug 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Chevy Uplander and I'm trying to connect a reverse backup camera to my car and I do not know which wire is positive for the reverse light bulb


open up the rear bulb compartment cover
and note the color wires running into the reverse light bulb holder

a hand full of fuses as you
use a LED test light or voltmeter to find the right wire

and use those color wires as your power /earth for the reverse camera

or you need the rear loom wiring diagram for that 2006 chev

Oct 13, 2016 | Cars & Trucks

1 Answer

Could some one please tell me where the reverse light switch on the gearbox is on a holden rodeo ra 05 thank you


07 Rodeo Reverse light switch...where is it? - Rodeo,Colorado and ...

forum.australia4wd.com > ... > Rodeo,Colorado and DMAX Technical

Nov 5, 2011 - 7 posts - ‎4 authors
posted in Rodeo,Colorado and DMAX Technical: My reversing lights ... switch as per workshop manual..could someone throw me a bone here...thanks. ... Started By rodeo5 , Nov 05 2011 04:35 PM ... My 4WD:RA 07 Rodeo; State:NSW ... would say the reverse switch would be on the gear box some where ...

Locate & Repair 96' Pajero Reverse Light Switch - YouTube

? 1:45
https://www.youtube.com/watch?v=osie5D_m-dA
Nov 12, 2010 - Uploaded by TwoMagadan
Locate & Repair 96' Pajero Reverse Light Switch ... Replacing ABack Up Light Switch On A Manual ...

Dec 14, 2015 | Holden Cars & Trucks

1 Answer

1994 Mitsubishi pajero.Where does the reverse light feed come from.To operated reverse alarm.Inside vehicle.Have checked vehicles reverse light switch.This is operating.Either there is another switch.


It comes from the transmission range sensor. When you put the lever in reverse the sensor on the transmission relays this to the backup lights.

Oct 20, 2014 | 1994 Mitsubishi Pajero

1 Answer

I want to install a back up camera on a 2013 altima and need to now what wire is the reverse light wire


There should be a good diagram in the wiring schematics that came with the camera. Follow the installation directions

Jan 18, 2014 | 2013 Nissan Altima

1 Answer

V46 mitsubishi pajero reverse gear is not working


run fault codes and look for a reverse solenoid/ servo or TCM fault.

Dec 16, 2013 | 1992 Mitsubishi Pajero

1 Answer

Can't get trailer lights to work on 2001 Pajero


Forget the fuses to begin with - you need to check each wire with a multimeter with the lights and ignition turned on to see whats happening at the plug end.

No multimeter? then get a 12v test lamp - (check first its working when connected to the battery it works). Now start with say the Tail lights on - connect the single wire from the test lamp to earth (a clean solid metal connection - like towbar) and then press the probe end against each wire in turn until you find the probe light turns or not. If it turns on then mark that wire as Tail - now do the same with the Stop light, then each Right/Left Indicator and then with the Brake light - either have someone press on the foot brake or else jam a suitable sized length of wood between the bottom of the steering wheel and the footbrake to hold it right down. You may also have a Reverse light as well.

You must have ignition ON to check, Stop, Reverse and Turn Indicator lights.
Hopefully this will locate each 'working' wire for you. Then you have to connect these to your trailer plug in the correct position - Google on your area if need be to see what pins are connected to what wires else when you plug the trailer in to the plug it still won't work.
Check out this website for pins and colours - make sure its applicable to your country - http://www.etrailer.com/faq-wiring.aspx as it may differ from country and vehicle..

If you find any wire that does not light up when probed - then check the fuse for that wire's use - ie. Tail etc. If that fuse is ok then check back from the plug to the fuse box as you may have a broken wire or disconnected plug. You will always have an Earth wire - this will not light up when probed - its colour is normally white.

Aug 19, 2013 | Cars & Trucks

2 Answers

2000 toyota camry check engine light. trac light on. when i step on breaks reverse square indicator on dash board goes on. No reverse lights and rear light indicator on.


wires are pinched and shorting together near the left (drivers side) trunk hinge. brake light power is feeding back through the reverse light wiring. this will also turn on the check engine light with a neutral safety switch malfunction code as the computer also sees this voltage in the reverse light circuit. Find and repair the wiring, pull the EFI fuse in the panel under the hood to clear the code. Hope this helps

Dec 27, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...