Question about 2004 Ford Freestar

Open Question

Ford free star 2004 THERE IS A VALVE ON THE RIGHT SIDE OF THE INTAKE MANIFOLD THAT OPEN THE RUNNER.IT HAS A VACUUM LINE TO IT SHOW THE DIAGRAM?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 ford f150 v6 and got a code saying my intake manifold valve is stuck open


Inspect the intake manifold runner solenoid/motor. Remove it and make sure the manifold runner is not stuck. If the runner moves freely, replace the motor. If it doesn't move replace the manifold. Remove the manifold and try to break it free with a lot of lube and patience. It usually doesn't work out to well. Worth a shot though.

Aug 05, 2016 | Ford Cars & Trucks

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

How to fix code p2004 on 2005 ford focus


you code is here

P2004 Ford Intake Manifold Runner Control Stuck Open Bank 1


Possible causes - Intake Manifold Runner Control (IMRC) monitor signal shorted to power
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Intake Manifold Runner Control (IMRC) solenoid
- Damage Powertrain Control Module (PCM)
- Blocked vacuum hoses
alt="What does this mean?"> What does this mean? Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P2004 Ford Description The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open.


Read more: http://engine-codes.com/p2004_ford.html#ixzz3lke1SreV

Sep 14, 2015 | Ford Cars & Trucks

1 Answer

2004 ford f 150 5.4 3V pulled intake fixed vac hose came off replaced imrc & still show intake runner control closed bank 1 Still has no power when I get in it to pass something any ideas?


Is your check engine light on ? Any codes ?

There are three basic types of intake air sub-systems:


  • Intake Manifold Runner Control (IMRC) electric actuated system

  • Intake Manifold Swirl Control (IMSC) vacuum actuated system

  • Intake Manifold Tuning Valve (IMTV)

These subsystems are used to provide increased intake airflow to improve torque, emissions and performance. The overall quantity of air metered to the engine is controlled by the throttle body.

Intake Manifold Runner Control (IMRC) Electric Actuated System
The Intake Manifold Runner Control (IMRC) Electric Actuated system (Figure 107) consists of a remote mounted motorized actuator with an attaching cable for each housing on each bank. Some applications will use one cable for both banks. The cable or linkage attaches to the housing butterfly plate levers. The 2.0L (2V) Focus IMRC uses a motorized actuator mounted directly to a single housing without the use of a cable. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder. One passage is always open and the other is opened and closed with a butterfly valve plate. The housing uses a return spring to hold the butterfly valve plates closed. The motorized actuator houses an internal switch or switches, depending on the application, to provide feedback to the PCM indicating cable and butterfly valve plate position.



Below approximately 3000 rpm, the motorized actuator will not be energized. This will allow the cable to fully extend and the butterfly valve plates to remain closed. Above approximately 3000 rpm, the motorized actuator will be energized. The attaching cable will pull the butterfly valve plates into the open position. Some vehicles will activate the IMRC near 1500 rpm.



WARNING: SUBSTANTIAL OPENING AND CLOSING TORQUE IS APPLIED BY THIS SYSTEM. TO PREVENT INJURY, BE CAREFUL TO KEEP FINGERS AWAY FROM LEVER MECHANISMS WHEN ACTUATED.




  1. The PCM uses the TP sensor and CKP signals to determine activation of the IMRC system. There must be a positive change in voltage from the TP sensor along with the increase in rpm to open the valve plates.




  1. The PCM uses the information from the input signals to control the IMRC motorized actuator based upon rpm and changes in throttle position.




  1. The PCM energizes the actuator to pull the butterfly plates open with the cable(s) or linkage.




  1. The IMRC housing contains butterfly plates to allow increased air flow.

Jun 29, 2015 | Ford Cars & Trucks

2 Answers

What does the code p2008 mean on a 2004 ford freestar minivan


Intake Manifold Runner Control Circuit/open bank 1

Apr 13, 2015 | 2004 Ford Freestar

1 Answer

Need vacuum system diagram for 1992 mercedes 300e


Big breather from valve cover to air cleaner, the small vac line runs from there to the FPR.



These next are standing in front of the car:

Intake manifold lower outer runs to EZL

Intake manifold lower inner (right side) goes to switchover vac valve on driver fender. The other side of this vac valve goes to the throttle body

Intake manifold lower inner (left side) goes to switchover vac valves on passenger side fender. These then go back to the EGR valve once making a loop under the distributor cap for whatever reason.

Intake manifold rear runs to a 'three' way valve (or 'Y' connector) on the secondary firewall. This is usually a vac leak.

Jan 20, 2013 | 1992 Mercedes-Benz Mercedes Benz 300 Class

1 Answer

Code P2004 Bank 1 runners stuck open, What is the fix for this?


Hi,

This code indicates Intake Manifold Runner Control Stuck Open, Bank 1

Its hard to be very specific about a fix on this as there are a few potential fixes including the outright replacement of the intake manifold. If the Manifold Flow Valve blades are seized in the intake manifold, the manifold will have to be replaced
However this code can sometimes have a very easy fix and if you are lucky you may find that it is caused by a split vacuum hose connecting to the actuator. A leak in the vacuum system will set the code and I suggest you check this out first as a potential cause.

Thanks for using FixYa.

Dec 05, 2009 | 2004 Ford Freestar

3 Answers

1998 ford windstar 3.8 with code p1538. Is this a


LOOKING IN CODE BOOK.POSSIBLE CAUSE TO YOUR PROBLEM THE IMRC COULD BE STUCK OPEN.OR THE IMRC ACTUATOR IS DAMAGED OR HAS FAILED.ALSO THE IMRC MONITOR SIGNAL CIRCUIT COULD BE SHORTED TO POWER GROUND OR SHORTED TO SIGNAL GROUND RETURN.

Oct 23, 2009 | 1998 Ford Windstar

2 Answers

Vacuum lines


Hello, I have the 1993 Ford Festiva shop manual in front of me. The vacuum hose on the Fuel Pressure Regulator goes to the intake manifold. The manual says that the fuel pressure is maintained at a constant 36.3 psi, and when the engine vacuum drops (caused by high fuel demand) it causes the fuel pressure to increase inside the regulator. There should be a vacuum diagram on the bottom side of the hood that will help to show you what vacuum port on the manifold that it attaches to. If the decal is gone, look on the intake manifold for a vacuum port that is open and causing a vacuum leak. I hope this helps.

Oct 15, 2009 | 1993 Ford Festiva

1 Answer

Check engine light came on


THERE IS A VALVE ON THE RIGHT SIDE OF THE INTAKE MANIFOLD THAT OPEN THE RUNNER.IT HAS A VACUUM LINE TO IT.FOR IT TO BE STUCK OPEN EITHER THE SOLENOID IS BAD,THE VACUUM LINE IS BAD OR THE RUNNER IS GUMMED UP WITH CARBON AND STUCK OPEN

May 15, 2009 | 2001 Mazda MX-5 Miata

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...