Question about 2005 Dodge Neon SXT
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
To replace the oil pan jack and place car in towers. Remove the undercover shielding and watch out for the exhaust that will also have to be move. Drain the oil pan. The holding bolts will be removed with appropriated tools. Tap with wood block to lose it. Once removed check the oil pump for damage. To replace make sure to used a proper gasket and sealant. Install all parts back.
Posted on Jul 05, 2008
TO answer all your questions, the red oring is for the oil pump pickup tube, one bolt will fix that, RTV sealet is used in the seperation seams at the timing cover and rear seal retainer, 1/6th thick bead, 1/4" wide at seams, has for the trans inspection cover remove it for the repair, 5 bolts will do that part, and rear bracket, then the pan is ready to come off... GOOD LUCK RDJRP
Posted on Aug 07, 2009
Oil Pan - Removal & Installation3.7L, 4.7L And 5.7L Engines
Negative battery cable Structural cover Front crossmember
NOTE Don-t pry on the pan. The gasket is integral with the windage tray, and doesn-t come out with the pan.
NOTE The double ended studs must be installed in their original locations.
Pan bolts and studs Pan
Oil pan gasket Oil pan. Tighten the bolts, in sequence, to 105 inch lbs. (12 Nm). Front crossmember Structural cover Negative battery cable
Fig. Oil pan bolt torque sequence-3.7L engine
Fig. Oil pan mounting bolt tightening sequence-4.7L engine
Fig. Oil pan alignment dowel placement-3.9L engine shown
Hope helped; TY for using Fixya (remember comment and rated this post).
Posted on Apr 14, 2010
Caravan, Grand Voyager, Town and Country, Voyager,
Oil Pan - Removal & Installation
Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan
Fig. Oil pan mounting bolt tightening sequence-3.0L engine
Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
3.3L & 3.8L Engines
Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket
New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
Hope helps (remember rated this).
Posted on Jun 25, 2010
Do you need to replace the oil pan it self or just the oil pan seal? This can been a DYI job, depending on your experience working with cars. You will need a your basic tools. (Jack Stands, Jack, Oil Container, wrenches and sockets, new oil and filter.) The first thing you will need to do is drain the oil. This is a good time to change your oil since you will be taking the oil pan completely off.
Steps to removing oil pan
1) Set car on jack stands or ramps in order to work under the car. (Be Safe, Be Smart!)
2) You will need a wrench or socket to remove oil drain plug and drain the oil out of the car
-This is a good time to change your oil, so replace oil filter as well.
3) Once the oil is drained you can take of the oil pan off. Most oil pans are just bolted. Not to hard to take of.
4) Once off this is a good time to clean the oil pan if your just replacing the gasket. Do not use lubricant cleaners like wd-40. Brake cleaner has worked for me, you can also ask your local auto shop or autozone for a good cleaner.
5)Replace the oil pan with new gasket making sure there are no tears in gasket and it sits well between the oil pan and engine block. (Make sure there is nothing in the oil pan as well that could cause harm)
6) once you replaced the oil pan its just as simple as putting oil back into your car like you are changing your oil.
Posted on Nov 02, 2010
Tips for a great answer:
Mar 09, 2015 | 2005 Dodge Caravan
Nov 19, 2011 | 2005 Dodge Neon
Nov 19, 2011 | 2005 Dodge Neon
Mar 18, 2011 | 1997 Dodge Neon
Nov 02, 2010 | 2002 Dodge Neon
Jul 02, 2010 | 2001 Dodge Neon
Mar 13, 2010 | 2001 Hyundai Accent
Jan 16, 2010 | 2002 Dodge Neon
Jul 04, 2008 | 2003 Dodge Neon
142 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: