Question about Hyundai XG350

Open Question

Torque sequence /

Im changing my valve cover gaskets and replacing plugs wires and boots.on my hyundai xg350L i want to know what is the tightning sequence for the head bolts/ Torque sequence for the intake.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

Ad
  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

tburtk
  • 158 Answers

SOURCE: i need torque specs for a 2004 dodge cummins 24

http://www.dieseltruckresource.com/dev/index.php

I suggest this website for your dodge truck needs.

Posted on May 13, 2010

  • 335 Answers

SOURCE: cylinder head bolt torque chevrolet 3.4

here is the troque spec for the cylinder heads.

Cylinder Head Bolt

  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Posted on Jun 19, 2010

  • 3640 Answers

SOURCE: i need the engine torque specs for 99 chevy malibu

99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Posted on Sep 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asked about torque specs for valve cover gasket on "06" Hyundai Accent1.6l. Also need pattern sequence.


Never used pattern sequence on valve covers in my life alwsys just snugged them down with no problem.

Nov 16, 2015 | Hyundai Cars & Trucks

2 Answers

How do you Replace Head Gasket for 2002 Nissan Sentra GXE ?


Big difference between valve cover gasket and head gasket. To replace head gasket, you must dissamble top end of engine and send the head out to be resurfaced and then install new head gasket. If it is a leaking valve cover it is much easier. Simply dissasemble and then clean valve cover and top of head from all debris and remove all old gasket material. Tighten back down in sequence and do not over tighten. these small bolts can be overtightened easily so go in sequence just like when you tighten lug nuts by skipping one as you go around. 10mm bolts require about 10 pounds or less torque.

Jul 18, 2014 | 2002 Nissan Sentra

1 Answer

Plugs getting wet with oil


Don't know what type motor you've got, but this same thing happened with a DOHC Saturn engine. In the inside of the valve cover there's an O ring in each spark plug hole, they need to be replaced. If this is the problem, you'll want to replace the valve cover gasket as well. Since you'll already have the valve cover off. Also when replacing the valve cover, be sure to tighten the valve cover bolts in the proper sequence and proper torque.

Feb 17, 2013 | Cars & Trucks

1 Answer

Changed valve cover gasket new wires now car idals rough


what year?
old posts, Im doing all Suz posts back to Jan1.2013
Ok this is called misfire.
misfire can happen at any speed or RPM even IDLE.
im sure you had the spark plug wires/ or COPS connected
wrong. and is fixed , now.

Jan 23, 2013 | Suzuki Forenza Cars & Trucks

1 Answer

I have oil leakin on top of my spark plug wires in the tube ive changed the valve cover gasket 3 times i even put high heat cilcone over around the spark plug tubes but all it does is slow it down im not...


Two things:

1. Make sure you torque the bolts down to the right specification, which is 83 inch pounds (or about 7 ft lbs). Work opposite end of the cover and start with a lower torque first (like 50 in lbs), then go up to 83. It's just a good practice.

2. If that does not work, get a Fel Pro gasket set VS50365R (pic below). What is special about this set is the really thin o-rings there in the middle. Those are the rocker arm tube seals. You need to take the rocker arms off in order to replace them, but this way you're doing a complete job and you probably won't have that issue again. If you don't want to get the whole set again (since you already replaced most of it 3x over), you can probably just go to a honda dealership and pick up the 4 you need.


44db60b.jpg
Here are the seals under the rocker arms:

ea6e49b.jpg
If you decide to do this yourself, it's a good idea to get a set of feeler gauges so you can properly gap the clearance from the rocker arms to the valves. Intake valves should be gaped to .010 in, and exhaust valves to .012 inches. Also, yes, you can take the rocker arm assembly off without removing the distributor...just take off that one bolt that is in the way. The torque for the bolts holding in the rocker assembly is 9 ft-lbs for the smaller 6x1mm bolts and 16 ft-lbs for the larger 8x1.25mm bolts. Here is the torque sequence...

94f3f23.jpg

Oct 06, 2010 | 1992 Honda Accord

2 Answers

I pulled a spark plug to change plugs and the spark plug wire boot was all wet from oil. The other three plugs were fine. The rest of the engine looked fine apart from the regular dirty engine look. No oil...


yes, the valve cover gasket is the only thing that can cause this, and yes, you have to remove the cover and put a new gasket in to fix. Please let me know if you have more questions.

Sep 09, 2010 | 1996 Saturn SL

2 Answers

Oil in spark plug well 02 nissan maxima what could cause this


On the DOHC: The Spark Plug Tube Seals (Washers) on the Valve Cover has developed a leak.
Install new seals.
Remove the Valve Cover to Install the Seals.
If the Valve Cover Gasket have not been replaced recently, go ahead and replace them as well, making sure you clean thoroughly BOTH surfaces before installing any new Seal Washers and Gasket.

Let me me know if this helped, or if you have additional information or questions. Feel Free to contact me on FixYa.com!

ps...I'm replacing (for free!) the Valve Cover Gaskets today on a 1994 Nissan Maxima. Looks like we both will have fun!
If you need the Valve Cover Torque Sequence / Specs let me know on the Comment Section of this Post.

Apr 12, 2010 | 2002 Nissan Maxima

1 Answer

Valve Cover Gasket


the oil was the cause of the misfire, the oil swells the rubber on the plug boots and interferes with the electrical connection from the wire to the plug. when you replace the gasket, remover the plug wires, marking which one went where, and use a spray electrical cleaner to remove the oil. make sure the rubber on the new wires isn't already swelled. before removing the plugs or valve cover, spray brake cleaner down in the holes and use compressed air or shop rags to get the hole shiny clean before removing plugs. remove plugs and clean them too. then reinstall plugs and remove valve cover. when replacing any gasket, use a razor blade on to clean the surfaces well. you can even spray a shop rag with brake clean and wipe it to make sure its clean. clean is important. reinstall cover with new gasket in place and torque bolts... be careful not to overdo it, they are small bolts and overtightening can flatten out gasket and cause more leaks. then just reinstall plug wires and off you go

Feb 20, 2010 | 2001 Dodge Caravan

1 Answer

Plugs and wires fouling out and covered in.


THE ROCKER COVER GASKET IS LEAKING OIL INTO SPARK PLUG TUBES OR HOLES VERY COMMON

Jun 07, 2009 | 2001 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...