Question about 2009 Toyota Matrix

Open Question

I wANT to replace rear disc brakes on 2009 matrix

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the vss on the 2009 corolla? i know its on the transaxle but Im having a hard time locating it..


http://www.toyotanation.com/forum/324-10th-gen-corolla-2nd-gen-matrix-suspension-brakes-wheel-forum/381204-2009-rear-speed-sensor-problem.html

Apr 07, 2015 | 2009 Toyota Corolla

1 Answer

2009 Suzuki swift hatchback automatic 40000km and squealing brake noise and engine light is on why?


The two matters are unrelated. The squeaking brakes are because you need new brake pads, if you have new pads... the mechanic failed to use brake shim grease which stops the squeak. In severe cases, the front disc brakes may be scored... scratched deeply and require replacement. If you replace the front disc pads, replace the rear brake shoes as well! The service engine light is timed by your dealer to remind you when to take your car in for a service check. Many models have a sequence of steps that one can find on-line to reset the service indicator light back to re-zero the count.

Mar 12, 2015 | Suzuki Cars & Trucks

1 Answer

How do I remove rear brake disc 2009 berlingo


jack up rear wheel making sure you place a choc in front of front wheel, remove the wheel, remove the brake caliper there will be 2 bolts at back of brake disc you will then be able to undo then centre nut to remove the disc , if replacing disc it is best practise to replace both sides and renew the pads at the same time

Sep 24, 2014 | Cars & Trucks

2 Answers

Car has no power after changing fuses with car on


If your vehicle was running while you
changed a fuse, you may have fried the computer.
Try disconnecting the positive(red side) cable on your
battery. Desconnect it for about 5 or 10 seconds
then reconnect it. This will reset everything.
That is, if you didn't fry the system. You might
want to check that fuse you replaced. For future
reference, only change fuses with vehicle off.

Jun 28, 2014 | 2009 Toyota Matrix

1 Answer

2009 matrix 115v power outlet not working


usually in side panels in the rear. well covered. have seen some under the back seat but its depends on what model the inverter is. hope this helps

Mar 23, 2014 | 2009 Toyota Matrix

1 Answer

My abs light in my TOYOTA matrix is always on. What is the problem with it.


could be a bad sensor, broken sensor ring, dirty brake fluid, low brake fluid broken sensor wire, have your car scan that way you will now exactly what the problem is.

Jan 21, 2014 | 2009 Toyota Matrix XRS

2 Answers

How to replace rear brakes


If they are disc brakes, if the cups have slots, holes, or any thing other then flat then you need to turn them in.( They do not push in.) They are part of your emergency brakes. You need a tool to turn them back in. You can buy one at the parts store. They make one that is a block that has 4 different types so you will get the right one.If they are drum brakes then I would get a Chilton's Manual for your car. This way you will have it for your next problem. If you don't want to do that then jack it up and make sure you have jack stands. Take both wheels off and do one wheel at a time. If you need to see how they go back then just look at the other side.

Apr 14, 2009 | 2009 Honda Accord

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
2009 Toyota Matrix Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...