Question about 2010 Ford Fusion Hybrid

Open Question

I have a vapor lock in my hearter system in my 2010 ford fusion hybird how do you get it out

There are no more details i just have a heater hose vapor lock

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chrisK1997
  • 103 Answers

SOURCE: hearter core hoses

they should bother have one end connected to tubes on the firewall, and the other ends will connect to the intake manifold, and one to the water pump

Posted on Feb 22, 2009

  • 4088 Answers

SOURCE: 1988 ford thunderbird (not se) 3.8L v6 vapor lock

Vapor lock cannot occur in a tank mounted fuel pump. The pump may be worn enough to lose it's pumping ability at high temperatures. Have you changed the fuel filter? Is the check engine light on? If so, rent a scanner, read the code(s) and follow them to repairs. What occurs when the temps reach 96 degrees?

Posted on Aug 25, 2009

dttech
  • 4803 Answers

SOURCE: 2010 Ford Fusion - After changing the oil, how do

You use the "Setup" and "Reset" buttons in the Information Center. The sequence of button-pushing is different for Hybrid and Non-Hybrid vehicles. The sequence for your car should be outlined in your Owner's Manual.

Posted on Dec 07, 2010

  • 90 Answers

SOURCE: Which fuse is the trunk light fuse on a 2010 Ford

look in owners manual for fuseblock diagram

Posted on Feb 27, 2011

  • 1 Answer

SOURCE: hearter in ford sport trac not blowing hot

blend door motor behind glove box is very weak. drop glove box door down. on top of fan box is a 3x3 cover over the blend motor, 3 screws hold it down. replace it,about 70 bucks or i just turn on heat and tap on the cover with a pocket knife to start it moving. it gos to heat,leave it alone.

Posted on Nov 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

1 Answer

Drivers door wont open from inside or outside on my 2010 ford fusion. Any ideas how to get it open so i can fix it


Somehow you will have to get inside the door panel. Either the door lock is engaged and not un-locking. Electric locks? Could be the inside door release handle had dis-connected somewhere in the system due to a broken plastic retainer clip. Not easy but just take your time to not break the trim on the door, remove screws wherever they are. Look on Google for a driver's door trim panel removal steps. I'm not sure if the panel is attached with push-pins or just lift up on it after the screws are out.

Oct 14, 2014 | 2010 Ford Fusion 1.6

1 Answer

Why is my 2010 ford fusion is throwing code po455. no gas cap required


P0455 is Evaporative Emissions System Leak Detected (Large) and means that there is a large leak in the system probably with one of the EVAP hoses near the fuel tank or EVAP canister or maybe even A leaky purge valve.

May 06, 2014 | Ford Fusion Cars & Trucks

1 Answer

Radio Display not working, radio and rest of entertainment system works fine


NO FUSE ISSUE . BAD CONTACT AT THE DISPLAY CONNECTOR IS MOST POSSIBLE CAUSE

Apr 10, 2014 | 2010 Ford Fusion 1.6

1 Answer

I had a hole in a heater hose that caused a vapor lock how do you get the vapor lock out


From cold, run engine without the coolant cap on, have heater control switch on hot, let the system heat up, be careful it may pump out some coolant till the thermostat opens, when the thermostat opens the water level will drop, check if heat is getting into the car, top up to max level and replace the coolant cap. Check coolant level later, when the engine has cooled down, top up required. DON'T REMOVE CAP WHEN ENGINE IS HOT

Dec 27, 2013 | 2010 Ford Fusion Hybrid

1 Answer

The heater jusst started to malfunction. Sometimes the air will blow warm sometimes it won't.


heater core may be clogged,take the hoses that are under the hood at the wall and flush the with a water hose if that dont work replace the heater core.not the hoses the holes at the firewall

Dec 03, 2013 | 2010 Ford Fusion 1.6

1 Answer

Are there any online instructions for replacing the thermostat on the 2006 ford fusion 4 cyl. thank you much!


2.3L Engine
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the 3 bolts and reposition the thermostat housing to gain access to the hose clamps.
  4. Remove and discard the gasket.
    • To install, tighten the bolts to 10 Nm (89 lb-in).
  5. Disconnect the heater hose from the thermostat housing.
  6. Disconnect the lower radiator hose from the thermostat housing and remove the thermostat housing.

6efb7cd.gif
Thermostat housing and related components—2.3L engine

To install:
  1. To install, reverse the removal procedure.
  2. Install a new thermostat housing gasket.
  3. Fill and bleed the cooling system

Dec 07, 2009 | 2006 Ford Fusion

1 Answer

Hearter core hoses


they should bother have one end connected to tubes on the firewall, and the other ends will connect to the intake manifold, and one to the water pump

Feb 22, 2009 | 1987 Ford F 350

Not finding what you are looking for?
2010 Ford Fusion Hybrid Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...