Question about 1997 Hyundai Elantra

1 Answer

Im replacing timing belt, accessory belts and water pump on my hyundai elantra gls 1997 sta wgn auto transmission. (1)Where is bolt to drain engine block coolant?(2)After removing front engine mountin

Im replacing timing belt, accessory belts and water pump on my hyundai elantra gls 1997 sta wgn auto transmission. (1)Where is bolt to drain engine block coolant?(2)After removing front engine mounting bracket bolts, engine does not lower enough to make room to remove belt. Do i have to remove also the mount bracket from body to make room?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

(1) No need to know if engine block coolant drain plug was available. Once the water pump was removed, all engine block coolant was drained. (2) After removing the three engine mounting bracket bolts, I also removed the mount bracket from the the body and made enough room to replace the timing belt easier.

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

2 Answers

I have no clue on how to replace water pump on a 1995 chrysler cirrus 2.5L. I have to do this myself I dont have the money for a garage.


This is found on the autozone.com website.

2.5L Engine
See Figures 3 through 7
  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.

This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.
  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.



0900c152800896a7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the water pump mounting bolts


0900c152800896a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Pull the water pump assembly off of the engine and inlet pipe


0900c152800896a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Open the water pump housing and examine for cracks or damage


0900c152800896aa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the water pump housing gasket using a scraper tool


0900c152800896ab.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes

  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.

To install:
  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks

Aug 20, 2011 | 1995 Chrysler Cirrus

1 Answer

WHER IS THE WATER PUMP


Try Chilton's or All Data for instructions. This is a 4.5 -5 hour ordeal for a professional and a 2 day mess for an amateur. Plus you must remove the timing belt on the 2.4L 4 Cylinder to get to the pump. Mess up here and you can damage your engine. WATER PUMP is sign with the ITEM 5 in the next diagram...

zjlimited_152.gif


  1. Disconnect the negative battery cable.
This procedure requires removing the engine timing belt and the auto tensioner. The factory specifies that the timing marks should always be aligned before removing the timing belt. Set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.

  1. Raise and safely support the vehicle to a level that allows access from above and below.
  2. Remove the right inner splash shield.
  3. Remove the accessory drive belts.
  4. Place a drain pan under the radiator drain plug. Drain and properly contain the cooling system.
  5. Support the engine using a floor jack and block of wood, then remove the right motor mount.
  6. Remove the timing belt, tensioner and camshaft sprockets.

WARNING With the timing belt removed, DO NOT rotate the camshaft or crankshaft, or damage to the engine could occur.

  1. Remove the rear timing belt cover to access the water pump.
  2. Remove the water pump attaching bolts.
  3. Remove the water pump.
zjlimited_153.gif


Fig. 1: Water pump location on the cylinder block-4-cylinder engines





Fig. 2: Water pump assembly-4-cylinder engines


To install:

  1. Thoroughly clean all sealing surfaces. Replace the water pump if there are any cracks, signs of coolant leakage from the shaft seal, loose or rough turning bearings, a damaged impeller or sprocket, or a loose or damaged sprocket flange.
  2. Install a new rubber O-ring into the water pump.
Make sure the O-ring is properly seated in the water pump groove before tightening the screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.

  1. Install the water pump and tighten the bolts to 105 inch lbs. (12 Nm).
  2. Using a cooling system pressure tester, pressurize the cooling system to 15 psi and check for leaks. If okay, release the pressure and continue the engine assembly process.
  3. Rotate the water pump by hand to check for freedom of movement.
  4. Install the rear timing belt cover.
  5. Install the camshaft sprocket(s), timing belt and tensioner. DO NOT allow the camshafts to turn while the sprocket bolts are being tightened, in order to maintain timing mark alignment.

WARNING Do not attempt to compress the tensioner plunger with the tensioner assembly installed in the engine. This will cause damage to the tensioner and other related components. The tensioner MUST be compressed in a vise.

  1. Install the timing belt covers.
  2. Install the right engine mount bracket and engine mount.
  3. Remove the floor jack and wood block from underneath the engine.
  4. Install the crankshaft damper.
  5. Install the right inner splash shield.
  6. Lower the vehicle.
  7. Install and tension the accessory drive belts.
  8. Refill the cooling system using the correct quantity and type of coolant. Bleed the cooling system.
  9. Start the engine and check for proper operation.
  10. Check and top off the cooling system, if necessary.
2.5L Engine
See Figures 3 through 7

  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.
This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.

  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.

Fig. 3: Remove the water pump mounting bolts



Fig. 4: Pull the water pump assembly off of the engine and inlet pipe



Fig. 5: Open the water pump housing and examine for cracks or damage



Fig. 6: Replace the water pump housing gasket using a scraper tool



Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes



  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.
To install:

  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks.

Hope this helps (remember to rate this answer).

Feb 01, 2011 | 1999 Dodge Stratus

1 Answer

How do you replace a water pump in a 2.5L V-6? Step by step.


2.5L Engine

  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly
    contain the engine coolant.
    NOTE: This procedure requires removing the engine timing belt
    and the auto tensioner. To help assure proper alignment at assembly, it may be
    helpful to set the engine at TDC on No. 1 compression stroke. This should align
    all timing marks on the crankshaft sprocket and both camshaft sprockets.



  3. Remove the accessory drive belts and crankshaft damper.
  4. Remove the right engine mount. This requires safely supporting the engine
    with a floor jack and wood block so the mount can be removed.
  5. Remove the timing belt covers.
  6. Remove the timing belt and tensioner.





    Fig. 3: Remove the water pump mounting bolts
    90903p54.jpg






    Fig. 4: Pull the water pump assembly off of the engine and
    inlet pipe
    90903p55.jpg






    Fig. 5: Open the water pump housing and examine for cracks or
    damage
    90903p56.jpg






    Fig. 6: Replace the water pump housing gasket using a scraper
    tool
    90903p57.jpg






    Fig. 7: Always keep the water pump's mounting bolts lined up
    with their correct mounting holes
    90903p58.jpg



  7. Remove the water pump mounting bolts.
  8. Separate the water pump from the water inlet pipe and remove the pump.
    To install:

  9. Thoroughly clean all sealing surfaces. Inspect the pump for damage or
    cracks, signs of coolant leakage at the vent, and excessive looseness or rough
    turning bearings. Any problems require a new pump.
  10. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to
    make installation easier. DO NOT use oil or grease on the O-ring.
  11. Install a new gasket on the water pump and fit the pump inlet opening over
    the water pipe. Press the assembly together to force the pipe into the water
    pump.
  12. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  13. Install the timing belt and timing belt tensioner. Set the timing belt
    tension.
  14. Install the timing belt covers. Install the right engine mount. Remove the
    floor jack and engine block from underneath the engine.
  15. Install the crankshaft damper.
  16. Install the accessory drive belts and set to the proper tension.
  17. Connect the negative battery cable.
  18. Fill and bleed the engine cooling system.
  19. Start the engine and verify proper operation, with no leaks.


prev.gif next.gif

Oct 29, 2010 | 1996 Dodge Avenger

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

How do i install a water pump for an Isuzu Rodeo, V.7 3.2 liter


Isuzu_Rodeo_Rodeo_Sport_1997-2004
Water Pump - Removal and Installation

3.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Upper radiator hose Timing belt. Refer to the Timing Belt procedure. Idler pulley Water pump
To install:


d2081b9.jpg

Fig. Exploded view of the water pump mounting

3702807.jpg

Fig. Water pump torque sequence. Apply LOCTITE® 262 to bolt number 3 (arrow)-3.2L and 3.5L engines

NOTE Apply Loctite® 262 to bolt number 3 prior to installation.
  1. Install or connect the following:
    Water pump. Tighten the bolts in two passes, in sequence, to 18 ft. lbs. (25 Nm). Idler pulley. Torque to 38 ft. lbs. (52 Nm). Timing belt Upper radiator hose Negative battery cable
  2. Fill the cooling system.
  3. Start the engine and check for leaks.

3.2L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cableRadiator hoseAccessory drive beltFront coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulley Water pump
    Negative battery cable Radiator hose Accessory drive belt Front cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulley Water pump

To install:

e6f48ad.jpg

Fig. Water pump bolt tightening sequence-3.2L engines
  1. Install or connect the following: Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm).Timing beltFront coverAccessory drive beltRadiator hoseNegative battery cable
    Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm). Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm). Timing belt Front cover Accessory drive belt Radiator hose Negative battery cable

  2. Fill the cooling system.
  3. Start the engine and check for leaks.

Hope this help (remember rated and commento).

Mar 19, 2010 | 1997 Isuzu Rodeo

2 Answers

Changing water pump 2000 ford focus


Changing a water pump is pretty basic. Since the coolant system is a closed system you only need to be concerned with that system. For instance you since you have to mess around with it anyway you might as well change the thermostat and flush the coolant system. Make sure your radiator hoses are in good shape and that's about it.
If you have basic mechanical skills and tools you will have no problem replacing a water pump.


As far as information with the actual replacement there are a number of experts here including myself that could explain how to do it.
However no matter how good our explanations are it just can't compare to a good repair manual.
A repair manual for your car at Auto Zone would likely cost between $12 and $15. It is a great investment if you are going to keep your car for any length of time. When you sell, it shows the buyer you took the time to maintain and repair it right.
I personally like Haynes Manuals.
I hope this helps.

Nov 11, 2009 | 2000 Ford Focus

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

1 Answer

Water pump


1. Drain the coolant and disconnect the coolant outlet pipe connection hose from the coolant pump. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt idler. 4. Remove the coolant pump mounting bolts, then remove the generator brace. 5. Remove the coolant pump assembly from the cylinder block. See an exploded view:
d0ab616.gif

Jun 27, 2008 | 1997 Hyundai Elantra

Not finding what you are looking for?
1997 Hyundai Elantra Logo

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...