Question about Dodge Ram 1500

Open Question

Dodge limp mode

Can not get truck to drive over 30mph

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: limp home mode

You need to scan for engine trouble codes. Most parts stores will do this for free, and tell you what they mean and make recommendations on what to do. The 'limp mode' kicks in to prevent damage to the vehicle when the computer gets data that something is wrong.. When you shut it off, it's temporarily reset, but then the cars computer is signaling there is still a problem, and it goes back into limp mode. If you have any questions after getting the codes 'read' , post questions and code #;s here for help. Good luck.

Posted on Apr 28, 2009

  • 14036 Answers

SOURCE: 2003 GMC Sierra 5.3L (has

CODE PO120 - TP SENSOR 1 SIGNAL RANGE PERFORMANCE. CODE P1516 - TAC MODULE THROTTLE ACTUATOR POSITION PERFORMANCE. CODE P2135 - THROTTLE POSITION SENSOR 1 - 2 CORRELATION ERROR. THIS IS A DEALERSHIP FIX YOU HAVE PROBLEMS OR FAULTS IN THE THROTTLE POSITION SENSOR.

Posted on Oct 24, 2010

renselff
  • 75 Answers

SOURCE: reset dodge magnium in limp mode

Limp mode can be reset as eaily as shutting off the car and restarting it. the computer will then retest the system, if the problem is gone you will not go into limp mode. but if the problem is still evident, you will have to have it repaired before it will work properly.

Posted on Jan 28, 2012

asetech74
  • 218 Answers

SOURCE: fault p1754 limp mode

This DTC is for an input clutch solenoid vavle function issue. This could be caused by a faulty Transmission Control Module (TCM), A bad terminal pin connection at the transmission harness connector, or a faulty or sticking control valve. My best solution i can provide to you is to take it either to the dealer where they can use the Consult II scan tool to monitor the transmission control functions, or somewhere that has an equivalent scanner to monitor these items. Hope this helps

Posted on Sep 08, 2012

  • 42218 Answers

SOURCE: how do i reset limp mode on f150

have the cpu reset with a reading tool. I would have a fault code check done as it is possible you have another fault.

Posted on Apr 21, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

4 cyl. Auto trans. in limp mode. takin the shift solenoid out to re build it i fnd ripped wires. My question may seem should i re connect the first or cont with the shift solenoi


Unfortunately, you should have gotten the diagnostic codes for the transmission before messing with the shift solenoid. Most of those dodge shift issues are caused by input and output speed sensors.

Feb 09, 2016 | 2002 Dodge Neon

1 Answer

Traction warning light comes on at 30mph and puts it in safe/limp mode - can't get faster but also doesn't slow down unless I press the break (even when not touching the accelerator)


Probly a computr issue...dont guess on parts. Unplug it and clean pins..then plug back in..see if car reboots. If no git it scand but find anothr mech. Go to surecritic.com

Jan 13, 2016 | Mini Cars & Trucks

2 Answers

Is in limp mode and wont go above 35 mph


Get an OBDII reader and connect to see what error codes you are getting. Limp mode can be caused by many different things including problems with the transmission.

Dec 19, 2015 | 2007 Chrysler 300

1 Answer

I was told my 08 dodge avenger was in"limp mode" ( doesn't excellerate as normal an won't do over 45) what do I need to do to repair this issue . thanks in advance.


Limp Mode is the result of an exceptional condition occurring. It provides the driver a very restricted driving mode to travel a limited distance,

One hopeful cause is that this has occurred when the car was first started. If it is then it is likely that the battery was weak and tripped the cars computer into the limp home mode. Some times the limp mode doesn't activate but a CK engine light comes on.

Make sure that the car is in a safe location. Make sure that the battery is charged. Remove the battery terminal for about a minute or two. Reinstall the battery connection. If the car starts normal and runs OK you can assume the battery voltage had dropped below an except-able level and tripped the limp mode. Replace the battery.

Nov 23, 2015 | Dodge Cars & Trucks

2 Answers

My car keeps randomly going into limp mode


O2 sensors will do this and many times will not leave a trouble code.

Dec 04, 2014 | 2003 Dodge Stratus

1 Answer

1997 dodge ram 2500 automatic in limp mode.


goes into limp mode when not functioning properly, could be a control solonoid, check fluid level first, but, the solonoid may be the problem

Mar 06, 2013 | Dodge Ram 2500 Cars & Trucks

2 Answers

04 ram will not shift past 35 mph


it may not be a transmission problem. have you checked for fault codes to make sure it is not in limp mode? limp mode keeps vehicle from accelerating properly because the ECM has put the system at a limited setting to keep the engine running but not to its full potential.

Jun 12, 2012 | 2004 Dodge Ram 1500

1 Answer

Reset dodge magnium in limp mode


Limp mode can be reset as eaily as shutting off the car and restarting it. the computer will then retest the system, if the problem is gone you will not go into limp mode. but if the problem is still evident, you will have to have it repaired before it will work properly.

Jan 28, 2012 | 2005 Dodge Magnum

1 Answer

I was driving down the road when suddenly the rpm went up and lost drive, was able to limp home at 30mph, All I had was low and reverse. Was told it could be the computer. Is this possible?


The computer put in fail mode so you could get home,more likely the trans is done for. Is the fluid dark? It is computer controlled,but if you were just driving ,I doubt the computer is at fault.

Dec 19, 2010 | 1996 Chrysler Town & Country

2 Answers

1997 isuzu wizard mu check light


Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Sep 08, 2008 | 1997 Isuzu Oasis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...