Question about Cars & Trucks

Open Question

C1514 vectra c

Code c1514 low voltage sencer

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: were is the camshaft sencer on a 2002 2.2dti vaxuhal vectra

on the timing chain side of engine near top

Posted on Mar 08, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Code is telling us that the float level sencer is showing low voltage and will not pass inspection

Fuel level sensor is bad. You can buy most of them online. $20 to $30. If you can't find yours, then you have to replace the sending unit. Around $200, Both in the fuel tank.

Apr 17, 2016 | Cars & Trucks

1 Answer

Code c1514 Mercedes benz

Good question. Any list I find skips from C 1513 past C 1514. Are you certain this is the code you get?

Mar 16, 2016 | Cars & Trucks

1 Answer

O2 sencer 4 wire color code

one will be power wire(5 voltage) one will be ground, one will be for the heater control, and the last will be the for the O2 variable voltage.

Jul 14, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

I have a code P0108 Map/Baro Circuit High Input does that mean that my map sencer is nogood

the map/baro circuit could have an internal short suppling incorrect voltage to the wrong need to check the voltages,ground,and return voltage at the sensor plug with it connected to the sensor with the key engine off and the car running to see if the sensor is getting the proper voltage and has a good ground,also check the plug itself as it could be the problem

Mar 18, 2011 | 2004 Dodge Caravan

1 Answer

The engine light just came on, I and the oil change and they told me it was a knock sencer P0332 Low Input Bank 2. The truck has over 50 k miles and have never done tune up on it. Will the sencer need to...

The low input means that the computer isn't getting enough infomation from that sensor, it could be a bad connection to it or most likely the sensor is faulty. The spark plugs would have no tie to it. Just for your infomation, the spark plugs that are in the truck are good for at least 100K miles and if one was faulty it would set a code such as p0300 [ random misfiring ] up thru p0308 [ p0301 being cylinder #1 and so on ].

Jan 28, 2011 | 2005 GMC Sierra

1 Answer


is 12v getting to the ignition coil,,is low tension side of coil shorting to earth,so killing the voltage build up in the coil,

Jul 07, 2010 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

ABS Light ON

try checking the wires going to each wheel hub or bearing. these are for your anti lock brake system. the wire could be broke on inside of insulation too so check carefully. can check wheel sencers by unplugint each one and checking with volt meter. very low voltage ( mili volts) while you turn the wheel.

Nov 09, 2009 | Chevrolet Cars & Trucks

3 Answers

Vehicle stalled wouldn'

P1391 is a timing referance code, your timing is crucial to engine operation, this can be caused by the crank and or cam position sencer. If you changed these and the problem still exists, maybe you got ahead of yourself. These two (2) sencers run in conjuntion with each other, if one is out of whack for any length of time, The ECU will trip and pretty much say to itself, The Timing chain is broken, fix me! Also note that these sensers are typacaly LOW FAIL items. So on especially vehicles with the 2.5Ltr. V6, If you suspect a sencer is bad and you change it, might be a good idea to change both sencers and the timing belt since like all belts it may be streching.

Apr 25, 2009 | 1998 Chrysler Concorde

1 Answer


what is the year make and model of the car?

Oct 17, 2008 | 2003 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13632 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides