Question about 2009 Mercedes-Benz CLC 200

Open Question

Pairing key fob with the car

I have renewed the key fob battery but it still will not open the door locks.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
onyeredson
  • 404 Answers

SOURCE: mercedes 1999 c200 key fob

Hello Haq!
Could it be the key just needs re-coding? maybe you are worrying to much as £177 would be about right as that would need coding etc., Try phoning your local Merc dealer or take the key and V5 to them for coding (Hopefully)
Good Luck!
Paul 'W'
Onyer~EDson(:0)~[><

Posted on Jan 06, 2009

Ad
  • 64 Answers

SOURCE: Key fob will not reset after replacing battery

replace the key fob, please contact mercedes, who will supply u with a pre programmed key, it will save u a lot of aggro in the long run

Posted on Mar 02, 2009

  • 510 Answers

SOURCE: have mercedes E class key fob will not open doors,

If key will not turn
Car battery flat,charge or jump to activate elec ignition

Posted on Feb 06, 2010

  • 1 Answer

SOURCE: c240 mercedes key wont turn seems locked

I have a 2001 C240 with the same issue. I removed the positive battery cable from the battery and kept it off for 30 seconds then replaced it. Everything was reset and the key worked.

Posted on Feb 10, 2010

  • 510 Answers

SOURCE: I have a mercedes 2004 ml270 and the central

Synchronization
Turn ignition switch to position II. Turn ignition switch to position 0 and remove key. Within 1 minute: Press and hold key lock button. Press unlock button 5 times. Remote control should now operate system. If not: Repeat procedure.
Programming
When
Key remote control added or replaced. System malfunction.
How
Keys can only be programmed using diagnostic equipment.

Posted on Feb 14, 2010

Testimonial: "Spot on work great thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key remote won't lock the door change fuse and battery in remote still don't work


Common Reasons Why Your Car Door Isn't Locking Properly The key fob battery is dead: This is one of the most common reasons why your car door lock is not working. If your locks aren't working, replacing the battery in the key fob could solve the issue. The key fob is faulty: If the battery isn't the problem, the issue may be with the fob itself. If you go to your car dealer, they can hook the fob up to a computer and make sure that the programming is still good. If it's not sending a signal, the fob will likely have to be replaced. A fuse is blown: If one door doesn't work, but others do, the problem could be a blown fuse. Replacing the fuse will correct the problem. This is a cheap and easy fix The solenoid is bad: Again, if one door doesn't work, but others do, the problem could be with the door lock solenoid. Replacing it may require removing the car door panel You have a broken wire: If the lock isn't getting power, hold the lock switch either up or down, and then open and close the door repeatedly to see if the lock will work. If it works sometimes, you probably have a broken wire

Sep 28, 2016 | Cars & Trucks

1 Answer

Get Door To Open With Dead Battery So I can pop the Hood Switch


I imagine the obvious answer is to use a key in the door lock cylinder. The reason you have done this is because there is no door lock cylinder! You only have a fob is my guess, that electronically opens the doors. Dead battery..and the fob no longer works. Don't worry, examine your fob and there should be a way to open it. Carefully open the fob and surprise! There is a key inside of it! Now take that key and there ahould be a key lock cylinder above your rear license plate. You should be able to open your rear hatch. Now somewhere to the drivers side in the rear compartment there should be some sort of pull you can use which will open the drivers door. Hope that helps you out!

Mar 04, 2015 | 2006 Chevrolet Corvette

1 Answer

CL220, fob wont open doors I can't get in the car, does this mean the battery is flat?


battery may be flat in the fob or the vehicle has forgotten the code for the fob. and will need resetting. change the battery use the key to open the door put key in the ignition. ( fob Ir old type leave fob off the key) turn to number 2 and press fob till doors lock and unlock. then its reset. dont be worried if the alarm goes off while doing this it will go off when the code is restored. if you have 2 fobs you will need to rest that one to.

Mar 17, 2014 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

After replacing the battery on the 2006 navara the remote key does


you need to re-pair the key fob to the car turn ignition to 2 and press the fob the doors should lock. press again and it should un lock it is then paired to the car again.

Jan 17, 2014 | Nissan Cars & Trucks

2 Answers

LDV Maxus 3.5 Drivers door lock initially wouldn't unlock with fob, will work with key. Now will not lock or unlock on fob. Back door will unlock with fob, but does not lock, it has to be locked


The problem is not the actuators, the fault lies in the central locking control unit under the dashboard, behind the glovebox, on the firewall. The CLCU is mounted with the connection terminals to the top resulting in condensation going onto the printed circuit board inside, if the damage started a while ago there is only 3 ways to go.

1. specialist firm to repair the CLCU.
2. Replace.
3. (As I did) buy a cheap remote control receiver with keyfob/s. Cut all wires off the multiplug, there are four pairs, a permanent live and permanent earth. Test each wire to earth on the van to identify the permanent earth FIRST. Then test pairs of wires across 12v/Earth noting which pairs actuate which lock.Isolate in pairs noting which wire has to be live to lock, (Reversed it will unlock) wire each pair into the relay on the remote receiver using the relay to changeover the polarity to each pair You will then be able to Lock/Unlock all the doors, throw the old CLCU away and mount the RCReceiver eslewhere to keep it dry. each door individually. I bought a 2 way RCReceiver and can lock/Unlock front doors seperate the the rear ones which is of far more use! Any decent electrician will tell you how to wire the relays. Job Done..... (100% Sure)

603d3609-f326-41be-a38e-a00bb8d6bdab.jpg

Feb 02, 2013 | Cars & Trucks

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

1999 porsche 996 replaced key fob battery disconnected battery now trunk releses are locked and cant access battery.How do you open frt trunk manually


Assuming the car battery is ok (if not, buy a male to male cigarette lighter at the auto store and connect to another car until charged enough to unlock the doors...but don't try to crank the ignition!). The trunks won't open if the battery went dead with the alarm set because arming the alarm physically locks the releases.

Sounds like the key code is switched off because you replaced the key fob battery. Try unlocking the car manual with the key in the door lock. Then switch the ignition on to reactive the keyless entry. If this does not work, you might also try pressing the fob unlock button with the key in the door lock until the dash led flashes.

Jun 10, 2010 | 1999 Porsche 911 Carrera

1 Answer

THE REMOTE WILL NOT LOCK OR UNLOCK DOORS. LOCKS WILL ONLY WORK WITH KEY.


have you tried the battery in the fob if yes then its the control box phone a auto locksmith to recode or renew said box note; the box is not inter changeable between cars there coded for each fob

Dec 15, 2009 | 1996 Nissan Maxima

3 Answers

2004 xtype jaguar key fob suddenly stopped working car locked and alarmed if i use key in the door will the alarm go off if so how do i stop it


Your key fob needs reprogramming, and yes the alarm will go off when you open the door, but you have enough time to put the key in the ignition which will prevent the alarm sounding. Car is usable until you get the fob sorted by locking and unlocking using the key.

Jun 07, 2009 | 2003 Jaguar X-Type

Not finding what you are looking for?
2009 Mercedes-Benz CLC 200 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...