Question about 2000 Mitsubishi Montero Sport

Open Question

2000 Mitsubishi Montero Endeavor Not locked I don't have the remote lock that arms the alarm I put the spare key in the ignition. The alarm sounds. I press the small orange light on the left of the steering wheel and the lights flash, the locks open and close, and the alarm remains on. This has turned the alarm off in the past. I have put the vehicle in gear and backed it up and driven it forward. I cannot deactivate the alarm. I am 6 months pregnant and on an island. I am not going to take the battery out on my own. ANY IDEA why this is happening?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Factory installed alarm won´t deactivate

Open the door insert key in ignition. turn to on

Now hold down the red button which should be flashing, untill silent

this will deactivate the alarm.


Posted on Jul 16, 2008

Ad

SOURCE: 1998 MITSUBISHI MONTERO POWER SEAT MOTOR

I FOUND AFTER SEVERAL TEST THAT THE PROBLEM WAS THE SWITCH CONTROL ATTACHED TO THE SIDE OF THE DRIVER SEAT NOT THE COMPUTER UNDER THE DRIVER (THAT COST A LOT OF MONEY) SEAT. MY BEST RECOMMENDATION CALL PITSTOP AUTO WRECKING AT (818)899-0226 THEY ARE SPECIALIST IN USED MITSUBISHI PARTS IN SUN VALLEY CALIFORNIA. IT MAYBE COST NO MORE THAN $150 AND IT IS EASY TO INSTALL

Posted on Oct 08, 2008

  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

yecalam13
  • 41 Answers

SOURCE: can a 2004 endeavor use 2003 montero lifters

I looked this up and got that a 2004 endeavor has a 3.8l and the 2003 montero has the 3.5l engine. the oil filters have different part numbers for each engine.

Posted on Jul 17, 2009

  • 1 Answer

SOURCE: I HAVE A 2002 MONTERO MITSUBISHI, THE DRIVER SEAT

you try moving your seat foreward when the car is on flat ground or when the rear is higher than the front.It also happen to my pajero fieldmaster

Posted on Nov 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to disable alarm in 1999 monterro sports


disconnect the battery...wait 30 mins and the pcm should reset.

Jan 07, 2015 | 1999 Mitsubishi Montero Sport

1 Answer

What can be wrongwith a 1999 Mits. Montero it won't turn over after chang.ing batteries?


dash lights blinking after battery replacement oftentimes means that the alarm has gone off need to put the key in the door and turn the lock if it is a factory alarm and you don't have the remote if its an aftermarket alarm you may need to remove it if you don't have the remote anymore

Sep 25, 2014 | 1999 Mitsubishi Montero Sport

1 Answer

How to start a proton savvy with no chip in key housing


If not the battery (replacement) then check to make sure the transponder is not missing from the remote. Should be a small plastic to slot in the key. If still not working then you may need to reprogram it. It can only work if you have 2 set of keys to put in the ignition:

[1] Take the key that needs programming put it in the ignition and turn to the on position and then press and hold in the alarm reset button..

[2] While still holding in the reset button turn the ignition off and remove the key..

[3] Re-insert the key and turn the Ignition to the ON position.

[4] Release the alarm reset button and then press it in once..

[5] Now with the ignition still switched on take hold of your SPARE key and press the lock button on your spare key..the alarm should "BEEP" once..

[6] Now press the Lock button on the key that has lost its programming..alarm should "BEEP" again..

[7] Switch ignition off.

Try that it should work

Feb 21, 2013 | Cars & Trucks

2 Answers

2003 Montero Sport Remote (FOB)


HI Kemp you might have too reprogram your key fob
check your owner Manuel for how to program key

Sep 09, 2012 | 2003 Mitsubishi Montero Sport

1 Answer

2005 mitsubishi endeavor the keyless entry works on all doors but the main one


locking solenoid has failed, might be the wiring in the door or the motor its self has gone.

Jul 28, 2017 | 2005 Mitsubishi Endeavor

1 Answer

We've lost the key fob and need to use the spare key to enter car with out alarm sounding.


if you unlock the driver door before opening it with the key you can turn the alarm off. Also taking it to a electronics place and having a keyless entry system will bypass the factory alarm as long as you tell them to hook it up and in most cases its less than buying a new factory remote. Also if you dont lock the car with the lock button from the driver door before you close the door the alarm will not arm.

Dec 27, 2010 | 2000 Saturn SL

1 Answer

Car alarm is really annoying


Are you locking the car with the key fob? If so yo must unlock the car also with remote or alarm will sound when you unlock with key.Or someone may have set your system to passive arming.If this is the case you local saturn dealer will probally reset it back for you.Hope this helps

May 15, 2009 | 2000 Saturn SL

1 Answer

Replaced the alternator, now anti theft won't disable


The ignition lock anti-theft switch (19A438) detects if the ignition key cylinder is broken or "slam pulled" during a theft. The ignition lock anti-theft switch is always monitored by the remote anti-theft personality (RAP) module. This allows the alarm system to be triggered in the case that the ignition lock anti-theft switch detects tampering of the ignition key cylinder (even in the event that the alarm is not active at the time).
Refer to the Section 501-14B for more details on the keyless entry remote transmitter (15K601).
The door open warning lamp switch (14018) communicates to the RAP module through the generic electronic module (GEM). This input to the RAP will cause the anti-theft alarm to be sounded if the anti-theft alarm was armed.
The door disarm switches are assembled into both LH and RH lock sets. The door disarm switch must be triggered before the mechanical lock unlocks. This is to prevent the anti-theft alarm from activating when it should have been disarmed.
The RAP module controls the anti-theft system and is the brains of the keyless entry system. The RAP module communicates with the GEM to request that the interior lights be turned ON/OFF with use of the keyless entry remote transmitter, and the GEM communicates to the RAP to inform when the door is opened. Refer to Section 418-00 for inter-module communication.
The RAP module has three wire connectors attached to it:
  • The antenna for the keyless entry remote transmitter.
  • 26 circuit connector (C256).
  • 22 circuit connector (C257).
In addition to the perimeter alarm that uses the door open warning lamp switch, the RAP module also uses the ignition lock anti-theft switch and the autolock/relock feature to prevent theft of the vehicle. For a full description of the autolock/relock system, refer to Section 501-14B .
The THEFT LED is found on the instrument panel between the tachometer scale and the needle pivot point. The LED is illuminated during prearming and flashes when armed or triggered.
Prearming and Arming the System
The system can be armed if:
  • The ignition is OFF.
  • The PANIC alarm is OFF.
  • All doors are closed.
There are two ways to prearm the system:
  • Press the LOCK button on the transmitter.
  • Open a door, press the power door lock button and close the door.
After 30 seconds the system will be armed and the theft indicator in the cluster will flash every two seconds.
Disarming an Untriggered System
An armed system will be disarmed with one of these valid actions:
  1. Pressing the UNLOCK button on the transmitter.
  1. Placing a key in the door and turning to UNLOCK.
  1. Turning the key to RUN or ACC.
The anti-theft alarm can be triggered by the following conditions:
  • The ignition cylinder is damaged with or without the RAP being armed.
  • A door is opened without disarming the armed RAP module.
The remote transmitter can activate a panic alarm which is similar to an anti-theft alarm, but does not deactivate the starter or cause the theft indicator to flash.
Disarming a Triggered System
If the system has been triggered, (the horn honks, the lights flash, and an external starter interrupt relay is engaged), the system can be disarmed by:
  1. Pressing the UNLOCK or PANIC button on the transmitter.
  1. Putting a key in the door and unlocking the door.
  1. Turning the ignition to RUN/ACC (Turning the key to RUN/ACC will not disarm an alarm that has been triggered by the ignition lock anti-theft switch.).

Apr 10, 2009 | 1997 Ford F150 Regular Cab

1 Answer

VEHICLE WONT START


Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:
  • protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
  • monitors the status of the ignition key lock cylinder.
  • is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
  • when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
  • protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
  • triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.
Once triggered, the system responds by:
  • flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
  • sounding the horn (13832).
  • disabling the starter circuit until the system is disarmed.
---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module
  • The remote anti-theft personality module is located behind the instrument panel (04320).
  • It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
  • The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.
-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove radio. Refer to Section 15-01 .
  1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
  1. Lower glove box.
  1. Remove two remote anti-theft personality module bracket retaining screws.
  1. Disconnect electrical connectors and alarm and lock system antenna (15603).
  1. Remove remote anti-theft personality module and bracket.
  1. Remove remote anti-theft personality module from mounting bracket.
Installation
  1. To install, follow removal procedure in reverse order.
  1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).

    34bdf35.gif
Components The system is composed of the following components:
  • remote anti-theft personality (RAP) module with integral antenna
  • alarm indicator LED
  • door lock cylinder switch RH, door lock cylinder switch LH
  • liftgate door lock cylinder switch (220A40)
  • hood switch (part of windshield wiper motor wiring (17A477))
  • ignition lock anti-theft switch (19A438)
The following vehicle components are also used by the anti-theft alarm system:
  • generic electronic module
  • power door lock switch (14028)
  • door open warning lamp switch (14018)
  • autolamp relay (14N089)
  • horn relay and bracket (13853) and horn (13832)
  • low beam headlamps
  • rear lamps (13404) and parking lamps (13200)
  • starter relay
  • door lock relays
  • keyless entry remote transmitter (15K601)
--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:
  1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
  2. Unlock any door with a key.
  3. Turn ignition switch to RUN or ACC.
  4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.
------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:
  • Open any door or liftgate.
  • Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
  • Dislodge the ignition key lock cylinder.
  • The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.
When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

  • low beam headlamps
  • parking lamps
  • horn
  • THEFT indicator
The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Mar 02, 2009 | 1998 Ford Windstar

1 Answer

New battery, can't reset alarm


remove the alarm,their might be a passive switch on the alarm to turn it off with a special key,if you dont have the key break the lock so you can turn it off or try to open case of alarm and look at wires and then dertimine which ones to join or break,every alarm inside is different so you will have to work it out.

Oct 30, 2008 | 2000 Mitsubishi Montero

Not finding what you are looking for?
2000 Mitsubishi Montero Sport Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...