Question about 2005 Jeep Liberty Limited

1 Answer

Jeep wont start

After replacing my battery jseep started for a few seconds then shut off like 5 times and now it wont start at all. please help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Jeep Master
  • 1,727 Answers

You have a security issue... needs to be flashed... check with the dealer but I believe this is going to be your issue

Posted on Dec 28, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fixincars
  • 335 Answers

SOURCE: 2000 jeep gc wont stay running

Lock all the doors unlock the doors with the key because the security system thinks its being stolen and it shuts off the injectors
Try another key the chip in yours may be defective.

www.aceautomotive1.com

Posted on Aug 16, 2008

  • 118 Answers

SOURCE: How can I reset my Factory Alarm on my Jeep it wont run

Alarm Module Reset Procedure
NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.
When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.
The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.
Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the lift gate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.
Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.
Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

Posted on Jan 28, 2009

  • 6982 Answers

SOURCE: 2006 Jeep Wrangler won't start

First, make sure you can turn the engine by hand. If you can't then the starter can't turn it either. Have someone else turn the key and look for the source of the click...may be a relay. Go over the starting circuit with a volt meter. Check for power at the starter main terminal and then with the key turned to "start" check for power at the trigger terminal on the starter. Check battery voltage and check relay operation.
You have a neutral safety switch on the transmission if its an automatic and a clutch switch if it's a stick. Check them as well. Make sure battery grounding on fender and block are also clean and secure.

Posted on Oct 02, 2009

Testimonial: "Will try! Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why would a 95 2.5liter jeep engine after replacing crank sencer start up run just fine then after shut off not start untill jumped and rev up high


Did you reset computer
You can do this by removing battery positive and leaving off for about 5 mins make sure you have radio code though

Mar 04, 2015 | Jeep Cars & Trucks

1 Answer

Changed battery jeep started for a few seconds then shut off now wont start at all


Call dealer , they may be able to help you with a "reinitialize key code" procedure.

Dec 28, 2013 | 2002 Jeep Liberty

1 Answer

I have a 1994 jeep grand cherokee manufactured in October 1993. The problem I'm having is that the jeep wont start. At first we had no gas, no spark. We checked crankshaft sensor...it's ok, but...


Try this. Lock and unlock the tail gate with the key and see if it will start. The battery must be hooked uo when this procedure is followed. Whenever the battery is disconnected, the security circuit shuts the ignition down.
When you hook up any battery, make certain that you connect the positive battery cable first and negatvie (ground) second.

May 16, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

2000jgc shuts off while driving. replaced crank shaft sensor, tighten battery connects, no check engine light comes on, no codes avalible. at times one codes does come up when check engine comes o2 sensor...


Have you checked the map sensor? I have known a few vehicles that did this. Sometimes it would go 5 miles, other times 30. Martin, they would get the same code, O2 sensor. If so, I would try to replace that and it probably will solve the issue. The car would die a few times a day. If you have anymore questions, let me know Martin. I am here to help you.

Feb 24, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I have a jeep grand cherokee laredo 1993, the security system have been activated and now when I start it, it will only stay started for a few seconds. tried turning the key all the way to the right and...


first use your remote, lock-unlock-lock-unlock 5 times. use the key to unlock the door. lock with remote. If this fails, disconnect battery for 5 min. reconnect, should reset control module..

Dec 09, 2010 | 1993 Jeep Grand Cherokee

1 Answer

I replaced the battery, now the truck wont start.how do i reset the security system?


To reset the security system:
  1. Open the hood;
  2. Disconnect the black battery cableand wait few minutes (2-5);
  3. Reconnect it;
  4. Turn your key in the driver door twice;
  5. hold the key turned for 2-3 seconds on the second turn;
That should do it. You will have to set all of your clocks after doing this though.

Hope helped with this. remember rated his help, good luck.


Nov 26, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Jeep wont start....


You may have a bad pump or pump relay. However a bad crank sensor can give similar symptoms. To begin with don't assume anything and therefore, test everything till you get it narrowed down a bit. Use a digital multimeter and find test instructions in most inexpensive manuals such as chilton or haynes, available at most larger parts stores.

Oct 20, 2009 | 2001 Jeep Cherokee

1 Answer

The air conditioner wont stay on.


Do you mean the blower motor? Check resistors.

Jun 29, 2009 | 2001 Jeep Wrangler

Not finding what you are looking for?
2005 Jeep Liberty Limited Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...