Question about Cars & Trucks

Open Question

Install lanoium How to install lanoium flooring

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

Rear vent controls not working


The rear blower motor switch and the rear floor console switch bezel are serviced only as an assembly.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear floor console.
Rear Blower Motor Switch

  1. Remove the rear floor console switch bezel by releasing the retaining tab located at each end of the switch bezel and pushing it out through the front surface of the console.
  2. Disconnect the wire harness connectors from the rear blower motor switch and the rear heated seat switches.
  3. Remove the rear heated seat switches from the rear floor console switch bezel by gently prying the switches free from the back of the switch bezel.
INSTALLATION
  1. Install the rear heated seat switches into the back of the rear floor console switch bezel. Make sure that the switch retaining tabs are fully engaged to the bezel.
  2. Connect the wire harness connectors to the rear blower motor switch and the rear heated seat switches.
  3. Install the rear floor console switch bezel into the rear floor console by pushing it in through the front surface of the console. Make sure that the bezel retaining tabs are fully engaged to the console.
  4. Install the rear floor console.
  5. Reconnect the negative battery cable.

Feb 20, 2014 | Chrysler Pacifica Cars & Trucks

1 Answer

Only cold air is available, what can I do to fix the blend door temporarily


I would repair the problem if I have to disassemble the varioius parts to get at the air doors --- In-Vehicle Temperature Sensor Removal & Installation To Remove:
In-vehicle temperature sensor ford-10-00-433.gif

  1. Remove the climate control head.
  2. While pressing the retaining tabs inward, remove the in-car temperature sensor.
To Install:
  1. While pressing the retaining tabs inward, install the in-car temperature sensor.
  2. Install the climate control head.
---
Air Door Actuators/Motors Removal & Installation Air Inlet Door (Recirculation) Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor onto the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor (Heater Air Damper) Door Vacuum Motor To Remove:
Panel/floor door vacuum control motor shield ford-10-00-403.gif

  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the vacuum control motor mounting screws.
  4. Lift, rotate and remove the panel/floor (heater air damper) door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor (heater air damper) door vacuum control motor on the door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Temperature Blend Door Actuator To Remove:
  1. Remove the integrated control panel.
  2. Remove the right-side lower instrument panel insulator.
  3. Lower the glove compartment.
  4. If equipped with Electronic Automatic Temperature Control (EATC), remove the 2 remote climate control module screws and position the module aside.
  5. Remove the temperature blend door linkage shield.
  6. Disconnect the temperature blend door electrical connector.
  7. Remove the temperature blend door actuator mounting screws.
  8. Remove the temperature blend door actuator.
To Install:
  1. Position the temperature blend door actuator on the plenum.
  2. Install the temperature blend door actuator mounting screws.
  3. Connect the temperature blend door electrical connector.
  4. Install the temperature blend door linkage shield.
  5. If equipped with Electronic Automatic Temperature Control (EATC), reposition the remote climate control module and install the 2 mounting screws.
  6. Raise the glove compartment.
  7. Install the right-side lower instrument panel insulator.
  8. Install the integrated control panel.
prev.gif next.gif

Nov 05, 2010 | 2000 Ford Taurus

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

How do I adust the emergency brake


There is an adjuster under the console. See instructions below from autozone.com:

    1. On vehicle with low series floor console:
    1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
    2. Remove the floor console front finish panel.
    3. Apply the parking brake, then remove the floor console rear finish panel.

    1. On vehicle with high series floor console:
    1. Apply the parking brake.
    2. Remove the floor console finish panel.

    1. Remove the adjustment nut clip.
    2. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.

      0996b43f80204da9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled
    3. Confirm the parking brake is applied.
    4. Install the adjustment nut clip.
    1. On vehicles with high series floor console:
      1. Install the floor console rear finish panel.

    1. On vehicles with low series floor console:
    1. Install the floor console rear finish panel.
    2. Install the floor console front finish panel. If equipped, install the manual transmission shifter knob by turning clockwise.
  • Sep 12, 2010 | 2004 Ford Escape

    1 Answer

    Location and removal of the air vent actuator. step by step on how to get to it and replace it. Air blows and I can control hot and cold but I cant change from floor to vent to dash. It just keeps blowing...


    Removal & Installation
    1. Remove the floor air outlet duct extension from the floor duct.
    2. Remove the center console, if equipped.
    3. Remove the screws from the center console duct, if equipped.
    4. Remove the center console duct, if equipped.
    5. Disconnect the electrical connection at the mode actuator.
    6. Remove the mode actuator mounting screws from the HVAC module.
    7. Remove the mode actuator as an assembly with the actuator cam.

    98d9332.gif
    Mode actuator location

    To install:
    1. Install the mode actuator as an assembly with the actuator cam.
    2. Line up the heater/defroster valve lever with the mode actuator cam slot.
    3. Line up the A/C valve lever with the mode actuator cam.
    4. Install the mode actuator mounting screw to the HVAC module and tighten to 14 inch lbs. (1.6 Nm).
    5. Connect the electrical connection at the mode actuator.
    6. Install the center console duct, if equipped.
    7. Install the screws to the center console duct, if equipped, and tighten to 14 inch lbs. (1.6 Nm).
    8. Install the center console, if equipped.
    9. Install the floor air outlet duct extension to the floor air duct.
    10. Calibrate the HVAC module actuators.

    Apr 18, 2010 | 2004 Chevrolet Tahoe

    1 Answer

    REPLACING HEATER CORE


    HEATER CORE REPLACEMENT REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws . 12. Remove the heater air outlet cover heat stakes with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws . 15. Remove the heater core cover heat stakes with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly.
    INSTALLATION PROCEDURE 1. Install a new heater core foam seal to the HVAC module assembly. 2. Install the heater core to the HVAC module assembly. 3. From the inside of the heater core cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 4. Install the heater core cover to the HVAC module assembly. NOTE: Refer to Fastener Notice in Service Precautions. 5. Install the heater core cover screws . Tighten Tighten all screws to 1.5 N.m (13 lb in) . 6. From the inside of the heater air outlet cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 7. Install the heater air outlet cover. 8. Install the heater air outlet cover screws (2). Tighten Tighten the screws to 1.5 N.m (13 lb in) . 9. Connect the rear floor air outlet duct to the heater air outlet cover. 10. Install the rear floor air outlet duct to the holes in the floor reinforcement. 11. Install the floor carpet. 12. Install the RH Instrument Panel Closeout/Insulator panel. 13. Install the LH Instrument Panel Closeout/Insulator panel. 14. Connect the inlet and outlet heater hose to the heater core. 15. Use J 38185 in order to reposition the heater hose inlet and outlet clamps to the heater core. 16. Install the fuel injector sight shield. 17. Fill the cooling system.

    Nov 13, 2009 | 2003 Chevrolet Monte Carlo

    2 Answers

    How to remove heater core from 2000 Pontiac Montana. Antifreeze leaking on floor.


    Wow I hope youre mechanicly inclined, big job the entire dash & carrier have to come out 7-15 hr job if you know what you are doing to much to list hear I would check heater hoses at fire wall first make sure they arnt leaking. I wish you well

    Aug 31, 2009 | Pontiac Montana Cars & Trucks

    1 Answer

    How can i find out my parking brake adjustments on my 2003 ford escape?


    Parking Brake Cable Adjustment Vehicle with low series floor console
    1. Remove the floor console front finish panel.
      1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
      1. Remove the floor console front finish panel.
    1. Remove the floor console rear finish panel.
      1. Apply the parking brake.
      1. Remove the floor console rear finish panel.
    Vehicle with high series floor console
    1. Remove the floor console finish panel.
      1. Apply the parking brake.
      1. Remove the floor console finish panel.
    All vehicles
    1. Remove the adjustment nut clip.
    1. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.
    1. Confirm the parking brake is applied.
    1. Install the adjustment nut clip.
    Vehicle with high series floor console
    1. Install the floor console rear finish panel.
    Vehicle with low series floor console
    1. Install the floor console rear finish panel.
    1. Install the floor console front finish panel.
      • If equipped, install the manual transmission shifter knob by turning clockwise.

    Jan 21, 2009 | 2003 Ford Escape

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    57 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...