Question about 1995 Chevrolet Suburban

1 Answer

U joints make noise - 1995 Chevrolet Suburban

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 796 Answers

They need replacing. Replace them.

Posted on Dec 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clunk noise when turning


Check the cv shaft boots, if they are torn the grease inside will have come out and now the joints inside are worn out. Worn cv joints will cause noises when turning.

Feb 20, 2017 | Ford Taurus Cars & Trucks

1 Answer

My ram 1500 makes loud clacking noises and it gets worse when the t-case is locked in four wheel drive hoping it's the tcase and not the front end but not sure how can I tell


I suspect that it is "U" joints or cv joints that is the problem
remove drive shafts and lock the t case in 4x4 and see it it makes the noise
refit the rear drive shaft after checking joints and if still no noise connect the front shaft. if the "U" joints checked out then it could be the joints in the drive axles at the pivot point ball
remove a hub drive plates and see if the noise is there
if it isn't then I would consider the joints in the axle shafts to be candidates for repair /replacement
it all has to do with the torque wind up when in 4x4 and any worn or failing joint will clack as it tries to work

Aug 02, 2016 | Cars & Trucks

1 Answer

Toyota camry


That usually is a worn CV joint. Go to a smooth surface like a parking lot, wind the windows down, and turn slow circles on full lock. If you hear that noise, it is probably the CV joints and not ball joint noise, since you are not going over bumps.
Also look at the CV rubber boots (2 each side) to find any splits in them. Those let grease out and dirt in, and rapidly end the life of a CV joint.

The individual joints can be replaced, but it isn't worth it. If worn out, get a complete re-manufactured front axle each side.

Jan 28, 2013 | Toyota Camry Cars & Trucks

1 Answer

Full lock grinding noise micra


A "CLICKING" NOISE WHEN TURNING USUALLY INDICATES A BAD CV JOINT. LOOK AT SIDE MAKING NOISE AT INNER AND OUTER CV RUBBER BOOTS...IF CRACKED OR TORN....PROBABLY NEED NEW CV JOINT

Jul 30, 2012 | Cars & Trucks

1 Answer

I have a hyundai trijet 01 when turning right i get a clicking noise from front passenger wheel was wondering would it be the drive boll joints were changed


This noise is caused by a defective outer axle Constant Velocity joint. Look under the car behind the wheel that the noise comes from and you will likely see a rubber grease boot over the joint that is torn or otherwise damage. the joint must be replace in most cases.

Jul 12, 2012 | Cars & Trucks

2 Answers

2005 mini cooper knock felt through steering when turned to right noise does not continue on hard lock


Problem with a CV joint that is worn as it seem that the noise is heard only on partial turn. Try to find from which side the noise come from and replace the CV joint. Not serious if noise level is low and can be used if you do not mind the noise. Check however if the booth (cover) of the joints are intact and are filled with lubricant. Replace as soon as you can

Nov 19, 2009 | 2003 Mini Cooper

1 Answer

Rumbling noise at 30mph and above is it the cv joints?


sounds more like rotors or hub bearings cv joints make a clicking noise while turning when their going bad

Feb 26, 2009 | 1997 Oldsmobile Aurora

Not finding what you are looking for?
1995 Chevrolet Suburban Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...