Question about 1999 Nissan Sentra

1 Answer

1999 sentry won't start

Won't start

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 33 Answers

Check battery,is it fully charged,battery terminals.sand the b/post ,,
also check is the b/light comes on on the i/cluster,recharge battery

Posted on Dec 29, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to start without a key


Yes ! without one you won't get pass the anti-theft system .

Jul 20, 2016 | 1999 Jeep Grand Cherokee

1 Answer

How do i fix a skim key problem with a 99 intrepid?


SKIM is short for sentry key immobilizer module. It uses a proximity sensor and a special "sentry" key to keep people from stealing your car. They are notoriously unreliable, and can only be programmed by a dealer or authorized mechanic (TRANSLATION: expensive test equipment required). They fail in strange ways, and you can't use a "copied" generic key. If your sentry key or sensor has failed, a dealership can get you going again quickly. If there is a communication problem or other strangeness happening, it could take a few hours for the tech to sort out. 25315837-dz1fkxf1fwolart5ai0divhk-3-0.gif 25315837-dz1fkxf1fwolart5ai0divhk-3-1.jpg

Dec 10, 2014 | 1999 Dodge Intrepid

1 Answer

1999 jeep cherokee laredo key sentry light is on and car wont start


Anti theft engaged ! Try disconnecting the negative terminal for about 3 min the reconnect it! Check it out on you tube !

May 03, 2014 | 1998 Jeep Grand Cherokee

1 Answer

Sentry key


does it have a remote start or whats the issue exactly..

Feb 10, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Sentry key light on


reset the auto shut down and it will start sounds like the anti theft is holding you out

Feb 10, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Replace starter and battery 1999 Mazda 626 still won't start


Won't start or engine won't turn over and try to start?

Aug 06, 2011 | 1999 Mazda 626

2 Answers

1999 jeep showing code p1686


P1686 is a SKIM (Sentry Key Immobilizer Module) no signal code. The keys have tiny chips in them that have to match the SKIM module for that vehicle, if they dont match then the engine will stop running after a few seconds. This is to keep theives from making a key and driving away with you vehicle.
First of all, do you have 2 keys? If so try the other one, if it works, then the other sentry key (the one that didn't work before) has bit the dust. If both do not work and both seem to have same symptoms, then it is quite possibly the module under the sterering wheel cover attached to back of ignition switch which reads the sentry key and if it gets signal from sentry key, then it sends a signal to pcm allowing start up to complete with no shutdown. If this unit is bad, unfortunuately just replacing it is no help, because after replacement a DEALER must then program both the unit and your keys. Make sure you give the dealer both keys, as both have to be reprogrammed to the new unit, if only one is done, the other will not work.

Apr 24, 2011 | 1999 Jeep Cherokee

2 Answers

If i replace the ignition cylinder in my 1999 jeep grand cherokee will i have any problems with the anti theft system


You should not have a problem, the ignition cylinder only transmits the ohm reading from the key to the anti-theft module and it does not produce its own ohm reading or any kind of signal.

Oct 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

When jump starting my 99 jeep GC I accidentally hit the negative post with a pos cable (hot) large spark and subsequently it would crank but not start. Sentry key light came on steady as did check engine....


Not sure, but if Sentry Light stay on, by shorting it, the anti-theft system stay on ! Unplug the battery for 30min's reconnect it, and try it again, alot of chance that the anti-theft system will reprogram and will function normally ! You can go to a Local Dealer with your Jeep they will reprogram the system and everything will be fine ! For the Check Engine, need a OBD2 Code Scanner or a Garage/Dealer Scanner to know the Code Stored in the PCM and it will tell if PCM is okay too !

Aug 10, 2010 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Nissan Sentra Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...