Question about 2004 Jeep Wrangler

1 Answer

6 cyl. - can not get it apart from the clutch housing

2004 Jeep Wrangler 4.0L - have the engine on a hoist ready to remove but can not get it to release from the clutch housing. How is this done?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 710 Answers

TURN THE FLYWHEEL A LITTLE AT A TIME TO REMOVE EACH OF THE BOLTS THAT HOLD IT TO THE TORQUE CONVERTER. BE CAREFUL. HOPE THIS HELPS. PLEASE KEEP ME INFORMED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK

Posted on May 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace the bell housing of a 1989 jeep wrangler 4-cyl 4x4?


why are you replacing the bellhousing?,it means you are going to have to pull out the motor or the gearbox/transfer case,whichever is easieast

Jul 04, 2014 | 1989 Jeep Wrangler

1 Answer

My son is getting ready to replace his clutch on his 1992 Jeep Wrangler 6 cyl 4.0 l when he returns from Afganistan soon and wants to know if there is any other "stuff" he should replace at the same time...


Always replace the 'throw-out' bearing (which pushes directly on the clutch pressure plate) even though it may be good now. There is a bronze pilot bearing in the end of the crankshaft that the shaft end of the transmission slides into and tends to wear after long use. If badly worn, it can cause minor vibration sometimes after a gear shift. To remove the bearing, you will need to rent or borrow a 'slide hammer' tool with a twin-fingered puller adapter. Make sure the flywheel surface is reasonably smooth and no debris clinging to the surface. This is important if the clutch was 'chattering' before when engaging. Buy a plastic clutch-disc alignment tool that you use during the installation of the disc and pressure plate. Hope this helps!

Oct 15, 2010 | 1992 Jeep Wrangler

1 Answer

How do i bleed the clutch slave cylinder on a 95 jeep wrangler


pump up clutch pedal really fast about ten times....leave it held to floor....open bleeder on slave cyl... repeat untill you have good pedal....may need to adjust master cyl. rod on clutch pedal to get more travel....good luck....Lee

Nov 06, 2009 | 1995 Jeep Wrangler

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard


synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

1 Answer

1991 jeep wrangler


yes it could be also check the fluid level!

May 14, 2009 | 1991 Jeep Wrangler

1 Answer

1991 jeep wrangler sahara shifting promblems


Your clutch is not disengaging. If it a hydrolic clutch chk. the fluid in resavor, Or slave cyl. for the clutch is bad, Or it has got air in it and needs to be bleed. This is a clutch problem, nothing wrong with trans. If its a manual clutch linkage its an ajustment thing. My best guess if its hydrolic slave cyl. went bad, or resavor is out of fluid.

Feb 10, 2009 | 1991 Jeep Wrangler

1 Answer

94' Jeep wrangler,6 cyl., clutch adj.


Check the cable operation with the vehicle off, wheels blocked, by having an assistant depress clutch pedal while under the vehicle. If everything appears to be functioning normally, then there may be an internal transmission problem. Does the Jeep hold itself if it is placed in gear, park brake off? Can it be moved while in this state? If it does hold, you may simply have a stretched cable, or a broken or damaged quadrant. The quadrant mounts to the firewall of the vehicle, just in front of the driver, under the dash. This is where the cable connects. Check this, and let me know if it does or doesn't help.

Oct 09, 2008 | 1994 Jeep Wrangler

3 Answers

2004 Jeep wrangler 4.0 - 6cyl overheating


I had the same overheating problem in my jeep ! My problem was finaly found out to be the clutch in my fan its a different kind of clutch system it work as this. When your jeep gets warmer the tighter your fan clutch gets .While cool your fan moves slowly. now to test your clutch just warm up your jeep and rev it up a bit if your fan dose not pick up speed then it is sliping.What will come out of this is that you fan will the seez and run full all the time. if you jeep dose not overheat wile moving then it is not your thermo stat period.

Sep 02, 2008 | 2004 Jeep Wrangler

2 Answers

2004 jeep wrangler 2.4 litre 4 cylinder


check the ground wirea at the dipstick tube,remove them all,and bend the ends of the wire,look for weak or broken wires, i bought several 4 cyl jeep that had problems at shift, fall on their face < after the engine settled back in to place,so wires made contact> just a thot. the ground wires are small the engine moves,when shifting.

Jul 29, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2004 Jeep Wrangler Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...