Question about 1996 Chevrolet Tahoe

1 Answer

How hard will it be to replace upper ball joint in a 1996 tahoe?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 159 Answers

Depends on how skilled you are

Posted on Dec 28, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: Replacing upper ball joint (2001 Silverado 1500)

try autozone for a diagram and assistance and you can also rent the tools needed for the job

Posted on Jan 18, 2009

  • 2002 Answers

SOURCE: upper and lower ball joints

Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.

Posted on Jul 14, 2009

  • 753 Answers

SOURCE: replace upper ball joint 2003 silverado 1500

The ball joints on both 2wd and 4wd upper are pressed in you need to remove snap ring and using a hammer pop out the old one out this is after you seperate the upper arm from the spindle. To install the new ball joint you should use a ball joint press that you can rent at most autoparts shops

Posted on Aug 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Upper and lowere control arm replacement


Where you buy your ball joints usually will rent (for free, just pay for it and then return it is what they do) a ball joint press. It's an easy job if you have any mechanical skills at all. The strut is what keeps the pressure on the spring, using the weight of the vehicle to compress the spring, just undo the strut, raise vehicle and the spring will relax and you can remove the upper control arm.

Jun 19, 2013 | 2007 Chevrolet Chevrolet Tahoe LTZ

1 Answer

How to replace ball joints on 1996 thunderbird


The upper ball joints are replaced with the entire control arm assembly. The lower ball joints are pressed in and out with the aid of a special press.

Oct 11, 2012 | 1996 Ford Thunderbird LX

1 Answer

Trying to change my upper ball joint. Passager side


For your problem,check out this few help links.

Click the link below to go through its procedure:----Upper Ball Joints inspection and replacement? http://howtobyme.blogspot.in/2012/02/upper-ball-joints-inspection-and.html------- How to Test Upper and Lower Ball Joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-lower-ball-joint.html------- How to inspect Upper and Lower Ball joint? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-lower-ball-joint.html------ How to Service Ball Joints on Car? http://repairhelpcenter.blogspot.com/2011/12/how-to-service-lower-ball-joints-on-car.html----------- How to Replace Ball joints? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-lower-ball-joints.html--------- Lower Ball Joints replacing on Mitsubishi car? http://howtobyme.blogspot.in/2012/02/lower-ball-joints-replacing-on.html
-------------These details will help.For more help,keep updated,with car brand,model and year.Thanks.Helpmech.

Oct 05, 2012 | Cars & Trucks

1 Answer

Hello, I am looking for torque specs on the upper ball joint nut 2003 chev tahoe


Tighten nuts to 52 lb ft. Tighten bolts to 81 lb ft. Tighten upper ball joint to steering knuckle nut to 147 lb ft. Tighten bolt and nut to 18 lb ft. Tighten brake hose bracket to 106 lb in.

Aug 04, 2011 | 2003 Chevrolet Tahoe

1 Answer

How to replace upper ball joint on a 1996 honda accord


go to this site for more info-- www.ehow.com/how_5668350_change-ball-joint-honda-accord.html hope this helps you. the upper ball joint you have to change upper arm to repair. you can only change lower ball joint on accords. go to site for more info.

Jan 29, 2011 | 1996 Honda Accord

2 Answers

Lower ball joint replacement 1996 ford taurus. wiil I need to remove the the joint houseing from strut?


You remove lower control arm of the chassis where they are located . Do not remove upper mounting strut bolts, remove only two bolts that hold strut to sterrink knuckle.

Jan 08, 2010 | 1996 Ford Taurus

1 Answer

How to change upper control arm on 1996 Honda Civic DX ?


UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
  3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
  4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
To install:
Use new self-locking nuts when installing the upper arm and strut.
  1. Install the upper control arm assembly into the strut tower.
  2. Connect the upper ball joint.
  3. Install the front wheels and lower the vehicle.
  4. With all four of the vehicle's wheels on the ground, torque the upper control arm nuts to 47 ft. lbs. (65 Nm). Torque the castle nut to 32 ft. lbs. (44 Nm); then, only tighten it enough to install a new cotter pin.
  5. Tighten the wheel nuts to 80 ft. lbs. (110 Nm).
  6. Check and adjust the vehicle's front end alignment.
The bushings on the front lower control arms are replaceable on most models.
This procedure requires the use of a press and may be above the skill range of the average driveway enthusiast. It is recommended that this procedure be done by a qualified machine shop if you are not skilled in the proper use of a press.
  1. Remove the lower control arm that is in need of new bushings.
It is recommended that both the left and right lower control arm bushings be replaced at the same time. The vehicles handling may become unstable if there are new bushings on one side of the car and worn ones on the other.
  1. Set up the control arm in a press.
  2. Using a impact socket of the correct length and size, press out the old bushing.
  3. Install the new bushing by slowly using the press to push it into the control arm.
  4. WARNINGExcessive force could cause the bushing to bend or tear so be careful.
  5. Once the bushing is properly seated in the control arm, remove the arm from the press and install it on the vehicle.

Apr 05, 2009 | 1996 Honda Civic

Not finding what you are looking for?
1996 Chevrolet Tahoe Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...