Question about Ford Cars & Trucks

Open Question

Water leak into cab

Need help to find solution, have taken vehicle to various glass fitment centers, no results

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

Water leak in cab of 86 toyota pu under blower fan


Hole in firewall rain leakin down and in. At least thats my prob. Some silicone should work

Nov 26, 2012 | 1986 Toyota Pickup 4WD

1 Answer

At what temp is my 99 cadi dts considered to be overheating. It has gone as high as 120? Should I be concerned.


The radiator cap regulates the water pressure inside the radiator. The reason the cap has various spring ratings is because the water is typically hotter than boiling point to match the requirement of the engine. Most engines operate best at above 100 degrees C, and this is why the water needs to be pressurized. Each engine's optimal temperature range may differ slightly from model to model, but most are fitted with a temperature gauge to allow the driver to judge for themselves if the vehicle is overheating.If your vehicle is operating above normal, then please check the following:
1) Radiator cap for fit and corrosion.2) Condition of radiator. Feel from top to bottom after running. If cold in one area, then this could indicate a blockage. (replace radiator)3) Remove and check thermostat. Place in a glass of hot water, and view its operation (should open). Place in cold glass of water and view (should close).4) Operation of radiator cooling fan.5) Addition of antifreeze. Antifreeze helps even out hot temperature within the engine and improves performance and running.6) Pressurize system and check for leaks.
If none of the above are issues, then remove temperature sensor and compare resistance to a new one at the same temperature. Replace if necessary.

Nov 02, 2012 | Cars & Trucks

1 Answer

My sunroof is leaking. Originally only leaked in very severe -heavy downpour, now leaks almost every time it rains. Water is leaking down driver side pillar inside vehicle. Looking for a diagram of drain...


weather stripping around glass, have to keep it soft with Vaseline or protectorate for rubber to keep seal, u may have to replace if its weathered, always a problem on sunroofs t tops etc..

Mar 24, 2011 | 2002 Ford F150 Regular Cab

2 Answers

The rear window to my van came off and shattered during a windstorm... i bought a window off of craigslist.. and can't install it. I dont need it to work,i just need it to go back on.. my bf is taking...


is it a fixed glass or a moveable glass.

Fixed glass is placed against a bead of urethane sealer, like caulking.

Window, Liftgate, Stationary Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: SAFETY GLASSES AND GLOVES MUST BE WORN.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use only urethane for after-seal to service air and water leaks in urethane seal. Failure to do this may result in additional leaks.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Remove window wiper pivot arm (17526) .
  1. Remove all window glass stops.
  1. Using Rotunda Glass Adhesive Cutter 118-00050 or Rotunda Deluxe Glass Adhesive Cutter 163-00001 or equivalent, follow manufacturer's instructions and cut seal and dam around entire outer edge of windshield glass (03100) .
  1. Remove glass from vehicle.
  1. Trim urethane left on flange with a utility knife or razor blade until surface is smooth and free of cuts. It is not necessary to remove all urethane from the flange if it is cured. However, at no point should existing urethane material exceed 2.54mm (0.10 inch). NOTE: If urethane has not cured completely, remove all uncured urethane using care not to smear urethane on component parts.
    Check flange sealing area for damaged sheet metal or foreign objects which may have caused, or may cause, glass breakage. Service sheet metal if necessary.
Installation
  1. If existing urethane on metal flange has become contaminated, cut away contaminated urethane with a utility knife or razor blade.
  1. If painted sheet metal has been exposed anywhere along the flange, apply Urethane Metal Primer WSB-M2G234-C or equivalent over the painted surface using a clean brush. NOTE: A minimum of 30 minutes is required for primer surface to dry.
  1. Place the windshield glass on a low, stable work surface, inside up. NOTE: Wipe off immediately after application because it flash-dries.
  1. Using a lint-free cloth, wipe outer 25mm (1 inch) of inside glass periphery with Urethane Glass Wipe WSB-M5B280-C2 or equivalent.
  1. Position mouldings on glass. ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Thoroughly shake and stir Urethane Glass Primer WSB-M2G314-B or equivalent to ensure uniform pigment mixing.
  1. Using a clean brush, apply primer around entire periphery of glass on inside surface as shown. (Allow at least five minutes drying time.)
  1. Properly align glass to body.
    1. Make sure lower windshield glass stops are in place at bottom of windshield glass opening.
    1. Place windshield glass into opening. Center it top and bottom, side to side, with about equal clearance around opening.
    1. Using masking tape or crayon, make alignment marks at points on both the windshield glass and the window opening.
  1. Remove windshield glass from vehicle and place back on work table.
  1. Apply an even bead of Urethane Adhesive WSB-M2G316-B on top of existing urethane around entire window opening using an air pressure cartridge gun. Air line pressure should be around 276 kPa (40 psi). The bead should be large enough to seal the windshield glass but not cause expulsion into vehicle.
  1. Install windshield glass onto vehicle, taking care to align marks on glass to those on body. This must be done within 10 minutes of applying urethane.


Dec 20, 2010 | 1995 Ford Windstar

1 Answer

'98 GMC Sierra is leaking water inside the cab on the passenger side when I have the A.C. turned on. I can see where the water is coming from, but I can't get it to stop leaking.


There is a drain under the vehicle under where the ac lines go into the vehicle cab',look directly below the ac lines,it is hard to find but it is there ,use compressed air ,like a air compressor or air tank,with a blow gun and blow the drain out,if it unclogs the drain,it will pour out like a water fall,if this was at all helpful,please rate thank you.

Sep 15, 2010 | 1998 GMC Sierra

1 Answer

1997 F250 Supercab rear window leaks ... seals have been replaced once .. even had window replaced .... started leaking again


fixed or moveable back glass?

Apply 203 mm (8 inches) of Liquid Butyl Sealer C9AZ-19554-B or equivalent meeting Ford specification ESB-M4G162-A between the two secondary sealing fins centered on each upper corner of the cab's back window glass opening.

Aug 17, 2010 | 1997 Ford F250 SuperCab

1 Answer

My 1993 dodge dakota sports is leaking water into the cab on the passenger side its not threw the air vents and my ac fuse blows out evertime it happens


The only way water can get into the cab is either a blocked air vent drain, leaking windscreen seal or rubber, damaged panel joint, badly sealing wiper arm. badly sealing door. Try and follow a possible trail. Water will move great distances before dropping so the leak could be far from the results.

Feb 26, 2010 | 1993 Dodge Dakota

1 Answer

The drains on my sunroof leak when it rains and water comes inside the vehicle. How do I unclog the drains?


A big leak with that model is the drain tray in the rear under glass has broken loose. To check the drains, park vehicle on an down grade, open the glass and pour a cup of water in on each side and the water should come out the front, Turn the vehicle around to check the rear the same way.

Dec 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...